background image

These symbols are intended to alert the 
user to the presence of important operating 
and maintenance instructions in the manual 
accompanying the appliance.

Go to:

 

www.star-mfg.com/scripts/manuals.aspx

 

 

to obtain this units installation & operations 

manual, warranty & other documents.

NOTICE

Using any part other than genuine Holman factory supplied parts 
relieves the manufacturer of all liability.

Holman reserves the right to change specifications and product 

design without notice.  Such revisions do not entitle the buyer to 
corresponding changes, improvements, additions or replacements 
for previously purchased equipment.

Due to periodic changes in designs, methods, procedures, policies 

and regulations, the specifications contained in this sheet are subject  

to change without notice.  While Holman Manufacturing exercises 
good faith efforts to provide information that is accurate, we are 
not  responsible  for  errors  or  omissions  in  information  provided 

or  conclusions  reached  as  a  result  of  using  the  specifications.  

By using the information provided, the user assumes all risks in 
connection with such use.

GENERAL SAFETY INFORMATION

This equipment is designed and sold for commercial use only by 
personnel trained and experienced in its operation and is not sold 
for consumer use in and around the home nor for use directly by 
the general public in food service locations.

Before  using  your  new  equipment,  read  and  understand  all  the 
instructions & labels associated with the unit prior to putting it into 
operation.  Make sure all people associated with its use understand 
the units operation & safety before they use the unit.

All shipping containers should be checked for freight damage both 
visible  and  concealed.   This  unit  has  been  tested  and  carefully 
packaged  to  insure  delivery  of  your  unit  in  perfect  condition.   
If equipment is received in damaged condition, either apparent or 
concealed, a claim must be made with the delivering carrier.

Concealed damage or loss - if damage or loss is not apparent until 
after equipment is unpacked, a request for inspection of concealed 
damage must be made with carrier within 15 days.  Be certain to 
retain all contents plus external and internal packaging materials 
for inspection.  The carrier will make an inspection and will supply 
necessary claim forms.

GENERAL INSTALLATION INFORMATION

The  unit  was  shipped  fully  assembled  and  ready  to  plug  into  a 

standard outlet specified for its voltage and amp draw.  If improper 

electrical supply is determined, contact a qualified electrician prior 

to using the unit.  Removal and replacement of the power cord 
and plug will void the warranty.  For assistance, contact your local 
authorized service agent for service or required maintenance.

Level unit using the adjustable feet under the unit (approximately 

1/2" adjustment).
Before using the unit for the first time, wipe down the exterior with 

a damp cloth.

Allow enough space around the toaster for adequate ventilation.  
Do not operate the unit without the crumb tray properly positioned.  
Overheating and poor toasting may occur.  Read all labels on the 
unit and follow their instructions.

MAINTENANCE AND REPAIRS

Contact  the  factory,  a  service  representative  or  a  local 
service  company  for  service  or  required  maintenance.   

Go to www.star-mfg.com/scripts/manuals.aspx to find a service 

agent near you.  Replacement cord sets must be purchased from 
Star Manufacturing International, Inc. or our authorized agents.

Should  you  need  any  assistance  regarding  the  operation  or 
maintenance  of  any  Holman  equipment;  write,  phone,  fax  or  
e-mail  our  service  department.    In  all  correspondence  mention 
the model number and the serial number of your unit, along with 
the voltage.

Business Hours:

  8 am to 4:30 p.m. Central Standard Time

Telephone:

 

(877) 242-0270

Fax:

 

(314) 781-2714

E-mail:

 

[email protected] 

 

[email protected] 

 

[email protected]

Website: 

www.star-mfg.com

Mailing Address: 

Star International Holdings Inc., Company 

 

10 Sunnen Drive 

 

St. Louis, MO 63143 

 

U.S.A.

MODEL

R2E-12BK-208 

Conveyor Toasters

Electronic Controls

Conveyor Toasters Installation Instructions

2M-Z15105, Rev. - 8/23/2011

CAUTION

Summary of Contents for Holman R2E-12BK-208






















Reviews: