background image

 
 
 

 

 

Preventative Maintenance 

 

 

 

Star Trac E-SM Preventative Maintenance 

 

E-SM 

 
 

PREVENTATIVE  MAINTENANCE 

With  durable,  high  performance  components,  the  Star  Trac  E-SM  StairMill  is  designed  for  heavy  usage 
with  minimal  maintenance required. To keep your Stepper in top condition, Star Trac strongly recommends 
performing  the  regular  daily,  weekly  and  monthly  pre-  ventive  maintenance  routines  outlined  below.  Any 
unusual  symptoms,  such  as  a  loud  continuous  noise  during  operation,  should  be reported to STAR TRAC 
PRODUCT SUPPORT DEPARTMENT at (800) 503-1221. 

 

DAILY  MAINTENANCE 

 

Remove  excessive  accumulations  of  dust,  dirt,  and  other  substances  by  using  a  clean,  soft  cloth  and  a 

non-abrasive  liquid  cleaner,  such  as  Formula  409

TM

  or  FANTASTIK

TM

.  Wipe  down  the  exterior  of  the 

display panel, hand rails, pedals, shrouds and heart rate grips. 

NOTE:  DO NOT spray the cleaner directly onto the Display Panel or heart rate grips. 
 

WEEKLY  MAINTENANCE 

Perform  the  following  services 
each week: 

 

 

Vacuum  the  floor  under  and  around 
the StairMill. 

 

 

Inspect  the  Display  Panel  mounting  screws  for  security,  and 
retighten if necessary. 

 

 

Inspect 

the 

Display 

Panel 

keypads for wear. 

 

MONTHLY MAINTENANCE 

Perform  the  following  services  each  month, 
or as needed: 

 

 

Check  that  the  steps  and  shrouds 
are secure. 

 

 

Check the hand rails for looseness. Tighten screws 
as necessary. 

 

 

Check  for  smooth  and  quiet  operation  of  all 
moving parts. 

 

 
MANAGER / MAINTENANCE  MODE 

After  using  your  Star  Trac  E-SM  StairMill  for  a  period  of  time,  you  may  wish  to 
change some of its settings. 

Summary of Contents for E-SM






Reviews: