manualshive.com logo in svg

Star Micronics PR921-24-A, Specification Manual, Page: 12 / 31

Share
Download
Star Micronics PR921-24-A Specification Manual Download Page 12

– 9 –

4.4 Presenter Motor General Specifications

Model:

Mabuchi Motor FK-180SH

Rated Voltage:

24.0 V

Voltage Range for Use:

21.6 V to 26.4 V (24.0 V ±10%)

Peak Current:

Approximately 1.0 A (24 VDC, 25

°

C)

Average Current:

Approximately 0.2 A (24 VDC, 25

°

C, including at startup.)

Usage Temperature Range: -15

°

C to +60

°

C

No Load Current:

Max. 30 mA

No Load Revolutions:

6600 

±

 850 rpm

Rated Load Current:

Max. 110 mA

Rated Load Revolutions:

5000 

±

 650 rpm

Direction of Rotation:

At Discharge: CW (Clockwise direction when looking from the motor output

shaft.)

At Recovery: CCW (Counterclockwise when looking from the motor

outputshaft.)

DC Motor Drive

Speed Control:

None

Drive and Control:

Voltage (24.0 V) is applied to the DC motor when stopped to start it.

Brake Control:

Stops by shorting terminals.  Shorting time is 200 ms.

Paper Discharge Speed: 300 mm/sec

Note 1: The above paper discharge speed reflects the value for recommended paper (thickness

of 65 mm) and a receipt length of 75 mm.

Note 2: The above paper discharge speed varies according to the environment of use (tempera-

ture, humidity, power voltage fluctuations, etc.).

Current (A)

Time (T)

Summary of Contents for PR921-24-A
































Reviews:

No comments