x
LITHIUM-ION LED SATELLITE LIGHT
INSTRUCTION MANUAL
SAT3S
SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE.
Copyright © 2015
Baccus Global LLC, Boca Raton, FL 33432
(877) 571-2391
BC
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not approved by the party responsible for compliance could void user’s
authority to operate the equipment.
SAFETY GUIDELINES / DEFINITIONS
DANGER:
Indicates an imminently hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING:
Indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION:
Indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
CAUTION:
Used without the safety alert symbol indicates potentially hazardous
situation which, if not avoided, may result in property damage.
RISK OF UNSAFE OPERATION.
When using tools or equipment, basic safety
precautions should always be followed to reduce the risk of personal injury.
Improper operation, maintenance or modification of tools or equipment could
result in serious injury and property damage. There are certain applications for
which tools and equipment are designed. Manufacturer strongly recommends that
this product NOT be modified and/or used for any application other than for which
it was designed. Read and understand all warnings and operating instructions
before using any tool or equipment.
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS
WARNING: Read all instructions before operating light. Failure to
follow all instructions listed below may result in electric shock, fire and/or
serious injury.
GENERAL SAFETY WARNINGS AND INSTRUCTIONS
WARNING:
This product or its power cord contains lead, a chemical known to
the State of California to cause cancer and birth defect or other reproductive harm.
Wash hands after handling.
INSTRUCTIONS PERTAINING TO RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS
WARNING – WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAUTIONS
SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING:
• To reduce the risk of injury, close supervision is necessary when the light is used
near children.
• Use only attachments recommended or sold by the manufacturer.
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK:
• Charge indoors only.
• Do not expose charging adapters or battery to moisture, water or any other liquid.
• Use only the charging adapter supplied by the manufacturer to recharge.
• When an extension cord is used:
– The marked rating of the detachable power supply cord or extension cord
should be at least as great as the electrical rating of this appliance.
– The cord should be arranged so that it will not drape over the countertop or
tabletop where it can be tripped over, snagged, or pulled on unintentionally
(especially by children).
– The extension cord should be kept dry and off the ground.
WARNING: FIRE HAZARD:
Keep light lamp away from materials that may burn.
CAUTION: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:
• The LED gets hot quickly. Do not touch the hot lens, guard or enclosure.
• Never place the light face down on any surface when lit, charging or not in use.
Never store the light face down on any surface.
• Never look directly into the light or shine the light into another person’s eyes.
• Keep sharp objects away from lens — it can crack or break.
• Do not expose this unit to extremely high temperatures.
• Do not drop or throw light. It contains a lithium-ion battery.
• Use only with either the AC or DC charging adapter and/or the USB charging
cable that are provided with unit. Plug in the charging cable at the light first,
then plug into the charging source.
• Do not overcharge: Recharge up to 5 hours maximum or until the charge status
LED indicator lights blue.
• After charging/recharging, disconnect charging adapter and wait 5 minutes before
use.
• Do not crush, cut, pull or expose the charging cable to extreme heat.
• Position the charging cable so it does not become entangled or become a safety
hazard. Keep the charging cable away from sharp edges.
• Do not open the light body casing. There are no user-serviceable parts inside.
• Do not operate the light without the lens in place.
• To reduce risk of damage to the charging cable, pull by the plug rather than the
cord when disconnecting.
• Do not attempt to charge the unit if the charging adapter is damaged – return
the charging adapter to manufacturer for repair or replacement.
SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM-ION
BATTERIES
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, BURST
HAZARD, OR INJURY TO PERSONS OR PROPERTY:
Lithium-ion batteries are small, compact and ideal for providing long-lasting power
to this unit. However, they must be used and charged properly. Improper use can
result in serious injury, fire, or death.
• Lithium-ion batteries can explode in the presence of a source of ignition. Do not
use the product in the presence of an open flame.
• Do not place this lithium-ion battery powered unit in fire or apply heat to it.
• Do not subject this lithium-ion battery powered unit to strong impacts or shocks.
The battery in this unit contains safety and protection devices which, if damaged,
may cause the battery to generate heat, rupture or ignite.
• Do not expose the lithium-ion battery to water or salt water, or allow the battery
to get wet.
• Avoid storing this lithium-ion battery powered unit in the basement, bathroom
or other areas of the house that are or may become wet or where humidity and
moisture may concentrate.
• Do not leave this lithium-ion battery powered unit in direct sunlight, or use
or store the unit inside cars in hot weather. Doing so may cause the battery to
generate heat, rupture, or ignite. Using the battery in this manner may also result
in a loss of performance and a shortened life expectancy.
• Never charge this unit near heat or flammable objects.
•
NEVER THROW WATER ON A BURNING LI-ION BATTERY! If a lithium-ion
battery does catch on fire, it will burn even more violently if it comes in
contact with water or even moisture in the air. A fire extinguisher must
be used.
Battery Charging and Capacity
This unit is delivered in a partially charged state – you must fully charge it before
using it for the first time.
When stored at room temperature with a full charge, Li-ion batteries will begin
to discharge from the time they are manufactured, even when unused. Deep
discharges also decrease their capacity. Battery life can be extended by the
following:
• Charge battery to full capacity before storage.
• Optimal storage temperature for this unit is between 5°C and 20°C (41°F and 68°F).
• Never discharge the battery fully.
• Charge after each use.
• Always charge at least once every 3-6 months if not in frequent use to prevent
overdischarge.
Transportation of Lithium-Ion Batteries
• Always check all applicable local, national, and international regulations before
transporting a unit containing a Lithium-Ion battery.
• Transporting an end-of-life, damaged, or recalled battery may, in certain cases, be
specifically limited or prohibited.
INSTRUCTIONS PERTAINING TO THE USB PORTS
•
IMPORTANT:
Some household USB-powered electronics will not operate with
the USB ports provided with this device. Check the manual of the corresponding
electronic device to confirm that it can be used with this type of USB port.
•
The USB ports do not support data communication.
They only provide
power to an external USB powered device (5V DC/1A using the light’s USB port
or 5V DC/2A using the USB ports on the AC or DC charging adapters). Make sure
the rating of equipment plugged into the each USB port does not exceed the
amperage stated.
• Do not attach USB hubs allowing connection of multiple personal electronic
devices to any of these USB ports on the light or charging adapters.
SAVE THESE INSTRUCTIONS
INTRODUCTION
Congratulations on purchasing your new
Stanley Lithium-Ion LED Satellite
Light
.
Read this Instruction Manual and follow the instructions carefully
before using your new light.
FEATURES
9
13
14
11
12
10
1
2
3
4
5
6
7
8
1. Main LED light
2. Folding light panels (3)
3. Battery/charge status LED indicator / translucent USB power button
4. USB port (for use with USB charging cable and charging adapters)
5. Power/light mode button
6. Folding hanging hook
7. Magnetic base
8. Pivoting head
9. USB charging cable (for use with 120 volt AC/USB and 12 volt DC/USB charging
adapters)
10. 12 volt DC/USB charging adapter
11. 12 volt DC/USB charging adapter LED Indicator
12. 12 volt DC/USB charging adapter USB port
13. 120 volt AC/USB charging adapter
14. 120 volt AC/USB charging adapter USB port
READING THE BATTERY/CHARGE STATUS LED INDICATOR
The battery/charge status LED indicator is located inside the translucent USB Power
Button. It lights or flashes in two colors to indicate the following:
When charging:
Blue: Battery is in a fully charged state.
Blue (flashing): Battery is in a partially charged state.
Red (flashing): Battery needs to be recharged.
When operating the USB port (once the translucent USB power button has
been pressed):
Blue: Battery is operating at full voltage.
Red: Battery is operating at partial voltage.
Red (flashing): Battery is operating at extremely low voltage. The built-in low
voltage protection has activated and the unit will automatically shut down. The unit
must be recharged immediately.
CHARGING/RECHARGING THE LIGHT
This unit is shipped in a partially charged state. Charge unit after purchase and
BEFORE first use using the 120 volt AC/USB charging adapter for up to 5 hours or
until the battery/charge status LED indicator lights blue.
Recharge after each use until the charge status LED indicator lights blue.
IMPORTANT: When the unit is not in use, we recommend that the battery is
charged at least every 3 to 6 months.
CAUTION: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:
• Never place the light face down on any surface when charging.
• Make sure the light is turned OFF during recharging, as operating the light can
slow the recharging process.
• Failure to keep the battery charged will cause permanent damage and result in
poor performance.
Charging/recharging using the 120 Volt AC/USB Charging
Adapter
1. Make sure the power mode button and the translucent USB power button are
both turned off* (the light is not lit and the translucent USB power indicator/
power button is not lit).
* The translucent button does not operate the light, only the USB power port.
2. Insert the USB charging cable into the USB port on the light.
3. Insert the other end of the USB charging cable into the 120 volt AC/USB
charging adapter.
4. Plug the 120 volt AC/USB charging adapter into a (powered) standard North
American 120 volt 60Hz outlet. The battery/charge status LED indicator will light
or flash in one of two colors (as described in the “Reading the Battery/Charge
Status LED Indicator” section) to indicate the charging status.
5. Charge up to 5 hours or until the battery/charge status LED indicator lights blue.
6. When charging is complete, first unplug the AC/USB charging adapter from the
power source, then disconnect the USB charging cable from the adapter and
the light. Store the adapter and cable in a safe place.
Charging/recharging using the 12 Volt DC/USB Charging
Adapter
1. Make sure the power mode button and the translucent USB power button are
both turned off* (the light is not lit and the translucent USB power indicator/
power button is not lit).
* The translucent button does not operate the light, only the USB power port.
2. Insert the USB charging cable into the USB port on the light.
3. Insert the other end of the USB charging cable into the 12 volt DC/USB charging
adapter.
4. Insert the 12 volt DC/USB charging adapter into the 12 volt DC accessory outlet
of a vehicle or other functioning 12 volt DC power source. The LED indicator
on the 12 volt DC/USB charging adapter will light green when it is properly
plugged into the 12 volt DC power source. The battery/charge status LED
indicator will light or flash in one of two colors (as described in the “Reading
the Battery/Charge Status LED Indicator” section) to indicate the charging
status.
Note:
Some vehicles require that the ignition be switched to the accessory position
in order to power the accessory outlet.
5. Charge up to 5 hours or until the battery/charge status LED indicator lights
blue.
6. When charging is complete, first unplug the 12 volt DC/USB charging adapter
from the 12 volt DC power source, then disconnect the USB charging cable from
the adapter and the light. Store the adapter and cable in a safe place.
CAUTION: TO AVOID THE RISK OF PROPERTY DAMAGE:
•
NEVER CONNECT THE UNIT TO A POSITIVE GROUNDED VEHICLE.
• The 12 Volt DC charging adapter must only be connected to batteries with a
nominal output voltage of 12 volts. The unit will not operate from a 6 volt battery
and will sustain permanent damage if connected to a 24 volt battery.
Charging/recharging using the USB charging cable and a
device with a USB power port (not supplied)
1. Make sure the power mode button and the translucent USB power button are
both turned off* (the light is not lit and the translucent USB power indicator/
power button is not lit).
* The translucent button does not operate the light, only the USB power port.
2. Insert the USB charging cable into the USB port on the light.
3. Insert the other end of the USB charging cable into a device’s functional USB
power port. The battery/charge status LED indicator will light or flash in one
of two colors (as described in the “Reading the Battery/Charge Status LED
Indicator” section) to indicate the charging status.
4. Charge until the battery/charge status LED indicator lights blue.
5. When charging is complete, disconnect the USB charging cable from the
device’s USB power port and the light. Store the cable in a safe place.
OPERATING THE LIGHT
The power/light mode button turns the light on and off; and is also used to select
the light mode.
Notes:
The battery/charge status LED indicator will not light during cordless operation of
the light.
To check the battery status, make sure the light is turned off, then press on the
translucent USB power button. The battery/charge status LED indicator will light
or flash in one of two colors (as described in the “Reading the Battery/Charge
Status LED Indicator” section) to indicate the internal battery status.
The battery/charge status LED indicator will automatically turn off if it detects
there is no USB output power for 10 seconds.
Operating the light cordless
Disconnect the charging cable or adapter, then select the light mode as follows:
High:
To turn the light on and use the main LED light only at high setting,
press the power/light mode button once.
Low:
To turn the light on and use the main LED light only at low setting,
press the power/light mode button a
second time.
Area:
To use the 3 light panels only, press the power/light mode button a
third time.
All:
To use all LEDs, press the power/light mode button a fourth time.
Off:
To turn the light off, press the power/light mode button a fifth time.
Flash:
To use all the LEDs flashing, press and hold the power/light mode
button anytime for about 5 seconds.
To turn the light off in flash mode, press the power/light mode
button once.
IMPORTANT:
If the light’s battery voltage is low, the built-in low voltage protection
will activate after a short period of operation, then the unit will automatically shut
down This is a special feature to protect the unit’s internal battery from damage.
Recharge the battery before continuing use.
Operating the light corded
Attach the appropriate cable or adapter as described in the “Charging/Recharging”
section. Operate normally the light as outlined in the previous section.
IMPORTANT:
The light will operate while either charging adapter or the USB cable
is attached, but will continue to draw power from the unit’s Lithium-Ion battery
while the light operates. This may cause the low voltage protection to activate and
shut the light down. Manufacturer recommends only operating the unit in corded
mode for a short period of time.
Unfolding and Folding the Light Panels
The three LED Light Panels can be unfolded or folded entirely or individually.
Unfold the light panels gently outward (to 90 degrees maximum). To return the
light panels to their original position for storage, fold the light panels gently back
until they touch the center of the unit.
CAUTION – TO REDUCE THE RISK OF PRODUCT DAMAGE:
• Do not attempt to “force” the light panel to unfold beyond its maximum angle.
• The light panel was designed to unfold or fold outward and inward only.
• The unfolded light panel is not intended to support additional weight. Do not
shake the light and attach or hang anything additional to the light panel or risk
of breakage may occur.
Adjusting the Pivoting Head
With the three LED Light Panels unfolded, the pivoting head allows the light to be
tilted forward up to 90° to direct the illumination as desired.
CAUTION: TO REDUCE THE RISK OF PRODUCT DAMAGE:
• Do not attempt to “force” the pivot head beyond its maximum angle.
• The pivoting head was designed to tilt forward only. Tilting it backward may
damage the unit.
• The pivoting head was designed to be used when the unit is hand-held or is
hanging or attached to a surface using its hanging hook or magnetic base. Using
it when the unit is placed on a uneven, inclined or non-metallic surface may cause
the light to fall over and sustain damage.
Using the Folding Hanging Hook and Magnetic Base
The folding hanging hook and magnetic base allow you to position the light
for convenient, hands-free operation. To use the Hanging Hook, unfold it to its
90-degree open position. To use the Magnetic Base, fold the Hanging Hook to its
storage position.
CAUTION: TO REDUCE THE RISK OF PRODUCT DAMAGE:
• When light is hung by the hanging hook or attached using the magnetic base,
do not shake the light or object that it is hanging from or attached to. Do not
hang the light from or attach the light to any electrical wires or anything that it
is not secure.
• Only use the hanging hook for hanging the light. The hanging hook is not
intended to support additional weight. Do not attach or hang anything additional
to the light or risk of breakage may occur.
OPERATING THE LIGHT’S USB PORT
The light’s USB port provides 5 volts/1A of DC power to an external USB powered
device.
1. Disconnect the charging adapter or cable and make sure the light is turned off.
2. Press the translucent USB power button to power on the USB port. The battery/
charge status LED indicator will light or flash in one of two colors (as described
in the “Reading the Battery/Charge Status LED Indicator” section) to indicate
the internal battery status.
3. Simply plug the USB device into the light’s USB port and operate normally.
4. Press the translucent USB power button again to turn off the USB port. Make
sure the translucent USB power button is in the off position (is not lit) when the
unit is being recharged or stored.
Note:
The light’s USB port will automatically shut down (the battery/charge status LED
indicator will automatically turn off) if it detects there is no USB output power for
10 seconds.
OPERATING THE 120 VOLT AC/USB CHARGING ADAPTER’S
USB PORT
Plug the 120 volt AC/USB charging adapter into a (powered) standard North
American 120 volt 60Hz outlet. Then simply plug the USB device into the USB outlet
and operate normally.
WARNING – TO AVOID THE RISK OF PROPERTY DAMAGE:
Always plug the
120 volt AC/USB charging adapter to the standard North American 120 volt 60Hz
outlet before plugging any devices into it.
OPERATING THE 12 VOLT DC/USB CHARGING ADAPTER’S USB
PORT
Plug the 12 volt DC/USB charging adapter into a vehicle’s 12 volt DC accessory outlet
or other functioning 12 volt DC power source. The LED indicator on the 12 volt DC/
USB charging adapter will light green to indicate that it is properly connected. Then
simply plug the USB device into the USB outlet and operate normally.
WARNING – TO AVOID THE RISK OF PROPERTY DAMAGE:
•
NEVER CONNECT THE UNIT TO A POSITIVE GROUNDED VEHICLE.
• The 12 volt DC/USB charging adapter must only be connected to batteries with a
nominal output voltage of 12 volts. The unit will not operate from a 6 volt battery
and will sustain permanent damage if connected to a 24 volt battery.
• Always connect the 12 volt DC/USB charging adapter to the 12 volt DC power
source before plugging any devices into it.
CARE AND MAINTENANCE
All batteries lose energy from self-discharge over time and more rapidly at higher
temperatures. When the unit is not in use, we recommend that the battery is
charged at least every 3 to 6 months.
If the unit gets dirty, gently clean the outer surfaces of the light unit with a soft
cloth moistened with a mild solution of water and detergent.
Except for the fuse in the 12 volt DC/USB charging adapter, there are no user-
replaceable parts. Periodically inspect the condition of adapters, connectors and
wires. Contact manufacturer to replace any components that have become worn
or broken.
Battery replacement/disposal
BATTERY REPLACEMENT
The battery should last the service life of the unit. Service life is dependent on a
number of factors including but not limited to the number of recharge cycles, and
proper care and maintenance of the battery by the end user. Contact manufacturer
for any information you may need.
SAFE BATTERY DISPOSAL
Contains a lithium-ion battery, which must be disposed of
properly. Recycling is required. Failure to comply with local, state
and federal regulations can result in fines, or imprisonment.
Please recycle.
WARNINGS:
• Do not dispose of the battery in fire as this may result in an explosion.
• Before disposing of the battery, protect exposed terminals with heavy-duty
electrical tape to prevent shorting (shorting can result in injury or fire).
• Do not expose battery to fire or intense heat as it may explode.
Fuse replacement in the 12 volt DC/USB charging adapter
2A FUSE
CENTER CONTACT
END CAP
1. Unscrew the end cap
counterclockwise and remove.
2. Remove center contact and fuse.
3. Check fuse with a continuity checker.
4. If blown, locate a replacement
2 amp fuse.
5. Replace the fuse, center contact and
end cap.
6. Screw end cap clockwise until it
is finger tight - DO NOT OVER-
TIGHTEN.
7. Test for proper operation of the
12 volt DC/USB charging adapter.
TROUBLESHOOTING
The light will not charge
• Check that the translucent USB power button is turned off.
• Check the connection to the AC or DC power source. Make sure there is good
contact.
• Confirm that there is functioning AC or DC current.
The light will not operate cordless
• Make sure the power/light mode button has been pressed firmly to turn the light on.
• Check that the translucent USB power button is turned off.
• The internal battery may be completely discharged. Charge the unit following the
directions given in this manual.
The light’s USB port will not operate
• Make sure the cable and/or adapter is disconnected from any live AC or DC power
source.
• Make sure the power/light mode button is turned off.
• Make sure the translucent USB power button is pressed to turn the USB port on.
• The light’s USB port will automatically shut down (the battery/charge status LED
indicator will automatically turn off) if it detects there is no USB output power for
10 seconds. Press the translucent USB power button again to turn the light’s USB
port back on.
• Make sure the rating of equipment plugged into the light’s USB port does not
exceed 1A continuous.
• The internal battery may be completely discharged. Charge the unit following the
directions given in this manual.
The 120 volt AC/USB charging adapter’s USB port will not operate
• Make sure you have live AC power to the outlet the 120 volt AC/USB charging
adapter is plugged into.
• Make sure the rating of equipment plugged into the charging adapter’s USB port
does not exceed 2A continuous.
The 12 volt DC/USB charging adapter’s USB port will not operate / LED
indicator on the 12 volt DC/USB charging adapter does not come on
• Check the connection to the 12 volt power source. Make sure there is good
contact.
• Confirm there is functioning DC current.
• The fuse inside may have blown. Replace the fuse following the instructions in
this manual.
• Make sure the rating of equipment plugged into the charging adapter’s USB port
does not exceed 2A continuous.
If the unit does not operate after taking the steps given above, contact the
manufacturer at (877) 571-2391.
ACCESSORIES
Recommended accessories for use with this unit may be available from the
manufacturer. If you need assistance regarding accessories, please contact
manufacturer at 1-877-571-2391.
WARNING:
The use of any accessory not recommended for use with this
appliance could be hazardous.
SERVICE INFORMATION
Whether you need technical advice, repair, or genuine factory replacement parts,
contact the manufacturer at 877-571-2391.
ONE-YEAR LIMITED WARRANTY
The manufacturer warrants this product against defects in materials and
workmanship for a period of ONE (1) YEAR from the date of retail purchase by the
original end-user purchaser (“Warranty Period”).
If there is a defect and a valid claim is received within the Warranty Period, the
defective product can be replaced or repaired in the following ways: (1) Return the
product to the manufacturer for repair or replacement at manufacturer’s option.
Proof of purchase may be required by manufacturer. (2) Return the product to the
retailer where product was purchased for an exchange (provided that the store is a
participating retailer). Returns to retailer should be made within the time period of
the retailer’s return policy for exchanges only (usually 30 to 90 days after the sale).
Proof of purchase may be required. Please check with the retailer for their specific
return policy regarding returns that are beyond the time set for exchanges.
This warranty does not apply to accessories, bulbs, fuses and batteries; defects
resulting from normal wear and tear, accidents; damages sustained during shipping;
alterations; unauthorized use or repair; neglect, misuse, abuse; and failure to follow
instructions for care and maintenance for the product.
This warranty gives you, the original retail purchaser, specific legal rights and you
may have other rights which vary from state to state or province to province. This
product is not intended for commercial use.
Please complete the Product Registration Card and return within 30 days from
purchase of the product to: Baccus Global LLC, One City Centre, 1 North Federal
Highway, Suite 200, Boca Raton, FL 33432.
Baccus Global LLC, toll-free number:
(877) 571-2391.
SPECIFICATIONS
Light
(Conforms to UL STD.73)
Bulb:
1 main LED bulb and 18 ultra bright LEDs
Battery:
Lithium-Ion, 3.6 V DC
Input:
5V DC, 2A
USB Output:
5V DC, 1A
120 Volt AC/USB Charging Adapter
(Conforms to UL STD. 60950-1)
Input:
120V AC, 60Hz, 0.25A
Output:
5V DC, 2A
12 Volt DC/USB Charging Adapter
(Conforms to UL STD. 2089)
Input:
12V DC, 1.1A
Output:
5V DC, 2A
Fuse: 2A
Imported by Baccus Global LLC,
One City Centre, 1 North Federal Highway, Suite 200, Boca Raton, FL 33432
www.Baccusglobal.com 1-877-571-2391
RD080615
SAT3S_ManualENSP_080615.indd 2
8/6/2015 10:57:26 AM
