PIVOTING LED BENCH LIGHT/
POWER STATION
INSTRUCTION MANUAL
PSL1000S
SAVE THIS INSTRUCTION MANUAL FOR FUTURE
REFERENCE.
Copyright © 2017
Baccus Global LLC, Boca Raton, FL 33432
(877) 571-2391
x
x
4
1
3
3
1
1
11
11
BACK OF UNIT
10
5
6
7
8
9
7
1
2
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not approved by the party responsible for compliance could void
user’s authority to operate the equipment.
SAFETY GUIDELINES / DEFINITIONS
DANGER:
Indicates an imminently hazardous situation which, if not avoided, will result in death
or serious injury.
WARNING:
Indicates a potentially hazardous situation which, if not avoided, could result in death
or serious injury.
CAUTION:
Indicates a potentially hazardous situation which, if not avoided, may result in minor
or moderate injury.
CAUTION:
Used without the safety alert symbol indicates potentially hazardous situation which, if not
avoided, may result in property damage.
RISK OF UNSAFE OPERATION.
When using tools or equipment, basic safety precautions should
always be followed to reduce the risk of personal injury. Improper operation, maintenance or
modification of tools or equipment could result in serious injury and property damage. There are
certain applications for which tools and equipment are designed. Manufacturer strongly recommends
that this product NOT be modified and/or used for any application other than for which it was
designed. Read and understand all warnings and operating instructions before using any tool or
equipment.
IMPORTANT SAFETY INSTRUCTIONS
WARNING:
This product or its power cord contains lead, a chemical known to the State of
California to cause cancer and birth defect or other reproductive harm. Wash hands after handling.
GENERAL SAFETY WARNINGS AND
INSTRUCTIONS
READ ALL INSTRUCTIONS
WARNING:
Read all instructions before operating the spotlight. Failure to follow all instructions
listed below may result in electric shock, fire and/or serious injury.
INSTRUCTIONS PERTAINING TO RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS
WARNING – WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAUTIONS SHOULD
ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING:
•
To reduce the risk of injury, close supervision is necessary when the appliance is used near children.
•
Use only attachments recommended or sold by the manufacturer.
WARNING – TO REDUCE THE RISK OF ELECTRIC SHOCK:
•
For indoor or dry location and household use only.
•
When an extension cord is used:
– The marked rating of the detachable power supply cord or extension cord should be at least as
great as the electrical rating of this appliance.
– The cord should be arranged so that it will not drape over the countertop or tabletop where it
can be tripped over, snagged, or pulled on unintentionally (especially by children).
– The extension cord should be kept dry and off the ground.
•
Do not store the unit outdoors.
•
Do not expose the appliance to water or any other liquid
CAUTION – TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:
•
Do not disassemble the unit. There are no user-serviceable parts inside.
•
All lights give off heat:
– Do not touch the light panel while operating.
– Keep combustibles away from the light panel. Extreme heat can cause fires.
•
Never look directly into the light or shine the light into another person’s eyes.
•
Keep sharp objects away from the lens — it can crack or break.
•
Do not expose this unit to extremely high temperatures.
SPECIFIC SAFETY INSTRUCTIONS FOR POWER CORDS
•
Don’t abuse power cords:
– Protect power cords from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from apparatus. Never carry the apparatus by
the cord or yank it to disconnect from the receptacle. Pull by plug rather than cord when
unplugging.
– Position power cords so that they do not become entangled or become a safety hazard.
– Do not crush, cut, pull or expose power cords to heat, oil, and sharp edges.
•
Ground fault circuit interrupter (GFCI) protection
should be provided on the circuits or
outlets to be used. Receptacles are available having built in GFCI protection and may be used for
this measure of safety.
DANGER: Never alter AC Power Cord or plug provided.
If it will not fit the outlet, have
a proper outlet installed by a qualified electrician. Improper connection can result in a risk of an
electric shock.
Extension Cords
An extension cord should not be used unless absolutely necessary.
Use of an improper
extension cord could result in a risk of fire and electric shock, and will void warranty.
If an extension cord must be used, make sure your extension cord is in good condition. When using
an extension cord, be sure to use one heavy enough to carry the current your product will draw. An
undersized cord will cause a drop in line voltage resulting in loss of power and overheating.
Power Cord Safety
The device is for use on a nominal 120 volt circuit, and has a grounding plug that looks like the plug
illustrated in Figure A. A temporary adapter, which looks like the plug illustrated in Figures B and C
may be used to connect this plug to a two-pole receptacle as shown in Figure B if a properly grounded
outlet is not available. The temporary adapter should be used only until a properly grounded outlet
can be installed by a qualified electrician.
DANGER
Before using an adapter as shown in the following illustration, be certain that center
screw of outlet plate is grounded. The green-colored rigid ear or lug extending from adapter must
be connected to a properly grounded outlet– make certain it is grounded. If necessary, replace the
original outlet cover plate screw with a longer screw that will secure the adapter ear or lug to outlet
cover plate and make ground connection to a grounded outlet.
SPECIFIC SAFETY INSTRUCTIONS FOR THE USB PORTS
•
IMPORTANT:
Some household USB-powered electronics will not operate with the USB ports
provided with this device. Check the manual of the corresponding electronic device to confirm that it
can be used with this type of USB port.
•
The USB ports do not support data communication.
They only provide a total of 2.1A (5V
each) to an external USB-powered device. Make sure the rating of equipment plugged into each USB
port does not exceed the amperage stated.
•
Do not insert foreign objects into the USB ports.
•
Do not attach USB hubs allowing connection of multiple personal electronic devices to any of the
USB ports.
SPECIFIC SAFETY INSTRUCTIONS FOR THE AC OUTLETS
•
Do not insert foreign objects into the AC Outlets.
•
Do not attach AC outlet taps or multi-outlet extension cords, or attach more than one electrical
appliance to each AC outlet.
•
Observe all Safety Instructions in the “Specific Safety Instructions for Power Cords” section of this
Instruction Manual.
SAVE THESE INSTRUCTIONS
INTRODUCTION
Congratulations on purchasing your new
Stanley
®
Pivoting LED Bench Light/Power Station.
Read this Instruction Manual and follow the instructions carefully before using your
new light.
FEATURES
1. Tool Storage Holder
2. Pivoting LED Light Panel (containing 45 LEDs)
3. Mounting Holes
4. 120V AC Cable and Plug
5. USB Ports (total of 2)
6 USB Power LED Indicator
7. AC Outlets (total of 4)
8. Resettable Circuit Breaker
9. 3-Position Rocker Switch for the LED Light Panel (High/Off/Low)
10. Screw and Wall Anchor (total of 2 each)
11. Mounting Brackets
MOUNTING THE LIGHT
The unit can be mounted on a flat wall surface using the supplied Screws and Wall Anchors, either
through the Mounting Holes or supported by the Mounting Brackets.
Through the Mounting Holes on the Front of the Unit
SCREW
WALL
ANCHOR
WALL ANCHOR (NOT SHOWN –
IN WALL BEHIND UNIT)
SCREW
1. Position the unit as desired on a flat wall surface near a functioning AC outlet. Mark a dot on the
wall through each of the two mounting holes on the front of the unit.
2. Using a 15/64 inch diameter bit, drill one hole for each of the dots marked on the wall to a depth
of approximately 1.18-1.37 inches.
3. Install one of the Wall Anchors in each of the holes. Check that the Wall Anchors are fully and
securely inserted into the wall.
4. Make sure the unit is mounted in the correct direction. Align and screw one of the Screws into
each of the Anchors through the two screw holes in the Mounting Bracket. Do not over-tighten.
Supported by the Mounting Brackets on the Back of the Unit
MOUNTING
BRACKET
SCREW
MOUNTING
BRACKET
SCREW
WALL ANCHOR
WALL ANCHOR
1. Position the unit as desired on a flat wall surface near a functioning AC outlet. Mark a dot on the
wall through the holes in each of the two mounting brackets on the back of the unit.
2. Using a 15/64 inch diameter bit, drill one hole for each of the dots marked on the wall to a depth
of approximately 1.37–1.57 inches.
3. Install one of the Wall Anchors in each of the holes. Check that the Wall Anchors are fully and
securely inserted into the wall.
4. Screw the Screws into each of the Anchors and leave a gap of approximately .19–.39 inches with
the Anchors.
5. Align the Mounting Brackets with the two Screws. Fit the Mounting Brackets over the heads of
the Screws. Make sure the unit is suspended in the correct direction.
CAUTION – TO REDUCE THE RISK OF PRODUCT DAMAGE:
•
Do not attach anything to or hang anything from the LED Light Panel itself.
•
Do not use the Tool Storage Holder to store tools whose combined weight is more than 10 lbs.
•
Before drilling holes, make sure that the surface is clear of anything that could be damaged.
•
Make sure the unit is mounted on a flat, level and stable wall surface, assuring that all screws are
tightened securely.
•
Only use the Screws and Wall Anchors provided with this unit.
OPERATING INSTRUCTIONS
LED Light Panel
OPERATING THE LED LIGHT PANEL
•
Plug the unit’s AC Power Cord into a (powered) standard North American 120V AC outlet.
•
Push the Rocker Switch to the upward position to turn the Light Panel on and use it in high
(brightest) setting.
•
Push the Rocker Switch to the downward position to turn the Light Panel on and use it in low
(dimmest setting).
•
To turn the Light Panel off, push the Rocker Switch to the center position.
PIVOTING THE LIGHT PANEL
The LED Light Panel can be tilted upward up to 90° to direct the illumination as desired.
CAUTION – To reduce the risk of product damage:
•
Do not attempt to “force” the LED Light Panel beyond its maximum angle.
•
The LED Light Panel was designed to tilt upward only. Attempting to tilt it downward from its
original position may damage the unit.
Using the AC Outlets
•
Plug the unit’s AC Power Cord into a (powered) standard North American 120V AC outlet.
•
Insert the plug from the 120 volt AC appliance into one of the AC Outlets and operate normally.
Note that the four AC Outlets can be used simultaneously.
•
To turn off all of the AC Outlets, unplug the unit’s AC Power Cord.
Notes:
The four 120V AC Outlets are protected by a circuit breaker located on the bottom of the unit. If any
of the 120V AC Outlets shuts down when it is in use, this circuit breaker may need to be reset. Do this
by pushing it back into the unit until it locks in place. Refer to the “Troubleshooting” section for more
information.
Using the USB Ports
•
Plug the unit’s AC Power Cord into a (powered) standard North American 120V AC outlet. The USB
Power LED Indicator will light blue to indicate the USB Ports are ready to use.
•
Plug a USB-power device into one of the USB Ports and operate normally. Note that the two USB
Ports can be used simultaneously.
•
To turn off the USB Ports, unplug the unit’s AC Power Cord.
Notes:
Refer to the “Specific Safety Instructions for the USB Ports.”
When the USB Port is in use, the unit will monitor for the following USB fault conditions: thermal fault,
overload and short circuit. If a fault condition exists, the USB Power Indicator will turn off and the USB
Ports will automatically shut down. Should this occur:
1. Unplug the unit’s AC power cord.
2. Disconnect the USB-powered device immediately.
3. Allow the unit to cool down for several minutes before attempting to use the USB Ports again.
4. If a fault occurs again, make sure that the total draw of all USB devices plugged into the USB Ports
does not exceed 2.1A.
5. If an individual USB device is within specifications and the fault occurs, have the USB device checked
for malfunction and do not continue to use it with this USB Port.
TROUBLESHOOTING
LED Light Panel will not light
•
Check that the unit is properly connected to a live 120 volt AC outlet.
•
Make sure the Rocker Switch is pressed to turn the Light Panel on.
AC Outlet will not power the appliance
•
Check that the unit is properly connected to a live 120 volt AC outlet.
•
Make sure the appliance is properly connected to the AC Outlet and that the appliance is turned on.
•
Mark sure that the total draw of all AC appliances connected to the AC Outlets does not exceed 15A.
•
The internal circuit breaker on the bottom of unit may have popped out, indicating that it needs
to be reset. Allow a cooling period of several minutes, then push the circuit breaker forward until it
locks back into the unit.
USB Port will not power the appliance
•
Check that the unit is properly connected to a live 120 volt AC outlet.
•
Make sure the USB Power Indicator lights solid blue. If a fault condition exists in the USB Port, the
USB Power Indicator will turn off. Refer to the Important Notes in the “Using the USB Port” section
to remedy any faults.
•
Make sure that the total draw of all USB devices plugged into the USB Ports does not exceed
5V/2.1A.
•
Some USB-powered household electronics may not operate with these USB Ports. Check the manual
of the corresponding electronic device to confirm that it can be used with this type of USB Port.
CARE AND MAINTENANCE
If the unit gets dirty, gently clean the outer surfaces with a soft cloth moistened with a mild solution
of water and detergent.
There are no user-replaceable parts. Periodically inspect the condition of the AC Power Plug and Cord.
Contact manufacturer to replace any components that have become worn or broken.
ACCESSORIES
Recommended accessories for use with your tool may be available from the manufacturer. If you need
assistance regarding accessories, please contact the manufacturer at (877) 571-2391.
WARNING:
The use of any accessory not recommended for use with this appliance could be
hazardous.
SERVICE INFORMATION
Whether you need technical advice, repair, or genuine factory replacement parts, contact the
manufacturer at (877) 571-2391.
ONE-YEAR LIMITED WARRANTY
The manufacturer warrants this product against defects in materials and workmanship for a period of
ONE (1) YEAR from the date of retail purchase by the original end-user purchaser (“Warranty Period”).
If there is a defect and a valid claim is received within the Warranty Period, the defective product
can be replaced or repaired in the following ways: (1) Return the product to the manufacturer for
repair or replacement at manufacturer’s option. Proof of purchase may be required by manufacturer.
(2) Return the product to the retailer where product was purchased for an exchange (provided that
the store is a participating retailer). Returns to retailer should be made within the time period of the
retailer’s return policy for exchanges only (usually 30 to 90 days after the sale). Proof of purchase may
be required. Please check with the retailer for their specific return policy regarding returns that are
beyond the time set for exchanges.
This warranty does not apply to accessories, bulbs, fuses and batteries; defects resulting from normal
wear and tear, accidents; damages sustained during shipping; alterations; unauthorized use or repair;
neglect, misuse, abuse; and failure to follow instructions for care and maintenance for the product.
This warranty gives you, the original retail purchaser, specific legal rights and you may have other
rights which vary from state to state or province to province. This product is not intended for
commercial use.
Please complete the Product Registration Card and return within 30 days from purchase of the product
to: Baccus Global LLC, One City Centre, 1 North Federal Highway, Suite 200, Boca Raton, FL 33432.
Baccus Global LLC, toll-free number: (877) 571-2391.
SPECIFICATIONS
Input:
120V AC, 60Hz, 1800W
Total Output:
1800W
Imported by Baccus Global LLC,
One City Centre, 1 North Federal Highway, Suite 200, Boca Raton, FL 33432
www.Baccusglobal.com 1-877-571-2391
RD092817
PSL1000S_ManualENSP_092817.indd 1
9/28/2017 10:52:30 AM
