Health and Safety
IMPORTANT
When installing the hardware the following should be noted. Please read
all these instructions and save them for later use.
The installation of this system must meet the requirements of the
country of installation’s National Wiring Regulations (BS7671, IEE
National Wiring Regulations in the UK) and EN60950-1. It must only be
carried out by suitably competent, qualified and experienced personnel.
Failure to do so can result in injury or death by electric shock.
It must also comply with any local Fire, Health and Safety regulations. A
secured door that may be part of an escape route must always be fitted
with the following.
l
A fail-safe lock so that the door will be released if the power
fails. Ideally a magnetic lock should be used as these are less
likely to jam or seize.
l
A normally-closed break-glass or manual pull in the lock supply
wiring so that in an emergency the fail-safe lock can be
immediately depowered.
Failure to do so may lead to injury or death in the event of a fire.
The controller must be earthed.
Isolate the controller power supply before working on the controller.
Failure to do so may damage the unit.
Cabling
The cabling used in the control systems, should be routed in a manner to
avoid running alongside any heavy load switching signals either within
equipment or wiring.
If this is unavoidable, cross the cable at right angles every 3.3–6.6ft / 1–
2m to reduce the interference.
ESD Precautions
The product contains static-sensitive devices and earth grounding strap
should be worn when handling the hardware.
RFID Devices
RFID technology is now widely used in a number of industries, it is
possible that interaction between your credential and other devices in
the vicinity may cause incorrect operation or recognition. Should you
suspect that you have experienced such a problem, ensure the interfering
device is out of range.
This only applies if any RFID devices have been fitted.
WEEE Directive and Product Disposal
At the end of its serviceable life this product should
not be treated as household or general waste. It
should be handed over to the applicable collection
point for the recycling of electrical and electronic
equipment or returned to the supplier for disposal.
Lithium Batteries
Failure to read the following guidelines carefully may result in injury.
There is a danger of explosion if lithium batteries are incorrectly replaced
or handled.
l
Ensure that lithium batteries are never short circuited.
l
Always store lithium batteries separately in non-conducting
materials.
l
Never replace a lithium battery with the incorrect type.
l
Lithium batteries are classified by the federal government as
non-hazardous waste and are safe for disposal in the normal
municipal waste stream. Fully discharge prior to disposal.
l
Lithium batteries contain recyclable materials and are accepted
for recycling by the Rechargeable Battery Recycling Corporation’s
(RBRC) Battery Recycling Program. Call 1 800 8 BATTERY or visit
http://www.rbrc.org for more information.
Product Information
This section will list all relevant directives, regulations and
specifications that apply to the GDX Audio & Video handset
(audio).
Product Specifications
Dimensions
W:120 mm × H:200 mm × D:40 mm
Weight
0.40 kg
Temperature
0 °C to +35 °C
Humidity
0% to 90% Relative Humidity
Input Voltage
12.0 VDC
Power
0.20 Amps Standby
Product Approvals Directives and Regulations
EMC
2014/30/EU
LVD SAFETY
2014/35/EU
RoHS
2011/65/EU
WEEE
2012/19/EU
https://pacgdx.com/compliance-declarations
GDX Audio & Video Door Entry
Audio Handset Installation and Programming
Ver. 11990707/1.3 May 2021
Technical Support
T: +44 161 406 3400 - opt. 2
Customer Services
T: +44 161 406 3400 - opt. 1
Training
T: +44 161 406 3400 - opt. 1
PAC & GDX is a division of STANLEY Security Solutions Ltd.
Registered in England and Wales No. 181585.
VAT No. 232 2446 95 Registered Office:
Stanley House Bramble Road Swindon Wiltshire SN2 8ER
T: +44 161 406 3400
Copyright 2020 STANLEY Security Solutions Ltd. All rights reserved.
This document or any portion thereof may not be reproduced or used in any
manner whatsoever without the express written permission of STANLEY Security
Solutions Ltd.
