Standard Change-Makers CMP-20 Page 50 Operating Manual Download | Manualshive

Page: 50 / 56

background image

Page 50 of 56

6.0

DOOR SWITCH MODULE BASIC INSTRUCTIONS

The Door Switch can be used to send email reports and/or alerts. The Door Switch Kit consists of a push button switch, a
cable and some mounting hardware. Alerts can be sent when the door opens and closes. Audit reports can also be sent when
the door is opened.

CONNECTING A DOOR SWITCH

:

(SCM P/N: 4K00439-FI or 4K00439–FI-01)

x

ROUTING THE CABLE: The door switch cable will connect the door switch to the EF+ Module. Route the door
switch cable (4C00232) using the existing cable clamps in the machine. Avoid routing cables where they can be pinched
by the door or other movable parts.

x

MOUNTING THE DOOR SWITCH: Assemble the brackets according to document 8M00638. Make sure that the
switch has good dependable contact with the door.

x

CONNECTING THE DOOR SWITCH TO THE EF+ MODULE: See the picture below for the EF+ Module
connection location. The cable is connected to the EF+ Module using at the AUX IN connection.

P/N – 4K00439

(EF+ Module Not Included)

Switch

1S00202

Cable

4C00232

«
...
48
49
50
51
52
...
»

Summary of Contents for CMP-20

























































Reviews:

No comments

Related manuals for CMP-20

Brand: Nautilus Hyosung Pages: 22

Brand: daviteq Pages: 17

Brand: Derovis Pages: 17

Money Machine 2

Brand: CUMMINS ALLISON Pages: 28

DARKFIELD QUEBEC 3325

Brand: Leica Microsystems Pages: 4

Brand: CUMMINS ALLISON Pages: 17

Brand: HYOSUNG Pages: 15

Brand: Texmate Pages: 6

VIPA FM 050-1BB30

Brand: YASKAWA Pages: 55

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands