Standard Change-Makers CMP-20 Page 42 Operating Manual Download | Manualshive

Page: 42 / 56

background image

Page 42 of 56

4.1.1

Dial-Up Modem

4.1.2

High Speed Modem

HIGH SPEED CARD PROCESSING:

Some credit card processors allow high speed card processing.

If your machine was ordered with this capability, it will be equipped with an IPTran module.

A device capable of being set as a DHCP server (router or switch) must be present at the site. This
device is not provided with the machine. The router or switch must be set to identify the Internet
Service Provider (company providing the DSL or cable service) as the DNS source. It must also be set
as the DHCP server. Both of these settings are configured in the device. Support questions for these
settings should be directed to the company the device was purchased from. Example device is a
Linksys router P/N – BEFSR41.

4.1.3

Troubleshooting The Credit Card Module

ISOLATING THE FAILURE

– Always attempt to isolate the module that is not functioning properly. To accomplish

this, you can use two basic troubleshooting tools present in the machine; the Version Number and the Demo operating
mode.

CHECK THE VERSION NUMBERS:

How to and why. Checking the version numbers will also indicate

whether or not the system is detecting the presence of each module. For example- if a version number is
not present for the credit card modem, them the system does not know one is connected. This in itself is a
significant troubleshooting clue.

USING THE DEMO MODE FOR TROUBLESHOOTING:

Once in this mode, the machine will operate as

though it has been plugged into a phone line or high-speed connection even if is not plugged into it. If the
machine processes credit card based transactions properly in this mode, yet fails when a live phone or
high-speed connection is used, there is a high probability that the issue is in the phone line and not the
machine.

Please see section 1.17.9 on how to initiate the credit card demo mode.

Important Note: The DialTran is compatible with a “land line” phone system. It will not
work with a VOIP (Voice Over Internet Protocol) phone system.

Note: Standard Change Makers is not able to provide assistance with IP network
setups at your business site. We recommend that you contact a local networking
expert for regarding networks.

NOTE: All DSL or Cable lines for the High Speed connection are to be supplied by the machine
owner. When routing these cables, please route through the same hole as provided for the machine
power cord.

«
...
40
41
42
43
44
...
»

Summary of Contents for CMP-20

























































Reviews:

No comments

Related manuals for CMP-20

LC4H-PS-R6-AC240V

Brand: Panasonic Pages: 8

Brand: ratiotec Pages: 20

Brand: Ampetronic Pages: 8

Brand: Met One Instruments Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands