background image

248568 / 647060300120

2019-02-13·BA00·III·en·04

Safety notes 

5

EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN
EN

Pendant Light Fitting LED

Series 6470/5

2.3

Symbols on the device

3

Safety notes

3.1

Operating instructions storage

• Read the operating instructions carefully.

• Store the operating instructions at the mounting location of the device.

• Observe applicable documents and operating instructions of the devices to be  

connected. 

3.2

Safe use

Before mounting

• Read and observe the safety notes in these operating instructions!

• Ensure that the contents of these operating instructions are fully understood by the 

personnel in charge.

• Use the device in accordance with its intended and approved purpose only.

• Always consult R. STAHL Schaltgeräte GmbH if using the device under operating  

conditions which are not covered by the technical data.

• We cannot be held liable for damage to the device caused by incorrect or unauthorised 

use or non-compliance with these operating instructions.

For assembly and installation

• Observe national assembly and installation regulations (e.g. IEC/EN 60079-14).

• Observe national safety and accident prevention regulations.

• During installation and operation, observe the information (characteristic values and 

rated operating conditions) on the type plates and data plates and information signs 

located on the device.

• Before installation, make sure that the device is not damaged.

Maintenance, repair, commissioning

• Before commissioning, make sure that the device is not damaged.

• Work on the device, such as installation, maintenance, overhaul, repair, may only be 

carried out by appropriately authorised and trained personnel.

• Perform only maintenance work or repair described in these operating instructions.

Symbol

Meaning

05594E00

CE marking according to the currently applicable directive.

02198E00

According to marking, device approved for hazardous areas.

Summary of Contents for 6470/5






























Reviews: