manualshive.com logo in svg

ST STM32L4 5 Series, Reference Manual, Page: 1202 / 1830

Share
Download
ST STM32L4 5 Series Reference Manual Download Page 1202

Real-time clock (RTC)

RM0351

1202/1830

DocID024597 Rev 5

TAMPxTRG bit. The internal pull-up resistors on the RTC_TAMPx inputs are deactivated 
when edge detection is selected.

Caution:

When using the edge detection, it is recommended to check by software the tamper pin 
level just after enabling the tamper detection (by reading the GPIO registers), and before 
writing sensitive values in the backup registers, to ensure that an active edge did not occur 
before enabling the tamper event detection.
When TAMPFLT="00" and TAMPxTRG = 0 (rising edge detection), a tamper event may be 
detected by hardware if the tamper input is already at high level before enabling the tamper 
detection.

After a tamper event has been detected and cleared, the RTC_TAMPx alternate function 
should be disabled and then re-enabled (TAMPxE set to 1) before re-programming the 
backup registers (RTC_BKPxR). This prevents the application from writing to the backup 
registers while the RTC_TAMPx input value still indicates a tamper detection. This is 
equivalent to a level detection on the RTC_TAMPx alternate function input.

Note:

Tamper detection is still active when V

DD

 power is switched off. To avoid unwanted resetting 

of the backup registers, the pin to which the RTC_TAMPx alternate function is mapped 
should be externally tied to the correct level.

Level detection with filtering on RTC_TAMPx inputs

Level detection with filtering is performed by setting TAMPFLT to a non-zero value. A tamper 
detection event is generated when either 2, 4, or 8 (depending on TAMPFLT) consecutive 
samples are observed at the level designated by the TAMPxTRG bits.

The RTC_TAMPx inputs are precharged through the I/O internal pull-up resistance before 
its state is sampled, unless disabled by setting TAMPPUDIS to 1,The duration of the 
precharge is determined by the TAMPPRCH bits, allowing for larger capacitances on the 
RTC_TAMPx inputs.

The trade-off between tamper detection latency and power consumption through the pull-up 
can be optimized by using TAMPFREQ to determine the frequency of the sampling for level 
detection. 

Note:

Refer to the datasheets for the electrical characteristics of the pull-up resistors.

38.3.15  Calibration clock output

When the COE bit is set to 1 in the RTC_CR register, a reference clock is provided on the 
RTC_CALIB device output. 

If the COSEL bit in the RTC_CR register is reset and PREDIV_A = 0x7F, the RTC_CALIB 
frequency is f

RTCCLK

/64

. This corresponds to a calibration output at 512 Hz for an RTCCLK 

frequency at 32.768 kHz. The RTC_CALIB duty cycle is irregular: there is a light jitter on 
falling edges. It is therefore recommended to use rising edges.

When COSEL is set and “P1” is a non-zero multiple of 256 (i.e: PREDIV_S[7:0] = 
0xFF), the RTC_CALIB frequency is f

RTCCLK

/(256 * (P1)). This corresponds to a 

calibration output at 1 Hz for prescaler default values (PREDIV_A = Ox7F, PREDIV_S = 
0xFF), with an RTCCLK frequency at 32.768 kHz. The 1 Hz output is affected when a shift 
operation is on going and may toggle during the shift operation (SHPF=1).

Summary of Contents for STM32L4 5 Series







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments