manualshive.com logo in svg

ST STM32F101xx series, Reference Manual, Page: 688 / 1096

Share
Download
ST STM32F101xx series Reference Manual Download Page 688

   

   

   

Serial peripheral interface (SPI)

RM0008

688/1096

 Doc ID 13902 Rev 12

Figure 243. TXE/BSY in Slave transmit-only mode (BIDIMODE=0 and RXONLY=0) in the case of

continuous transfers

Bidirectional transmit procedure (BIDIMODE=1 and BIDIOE=1)

In this mode, the procedure is similar to the procedure in Transmit-only mode except that the 
BIDIMODE and BIDIOE bits both have to be set in the SPI_CR2 register before enabling the 
SPI.

Unidirectional receive-only procedure (BIDIMODE=0 and RXONLY=1)

In this mode, the procedure can be reduced as described below (see 

Figure 244

):

1.

Set the RXONLY bit in the SPI_CR2 register.

2. 

Enable the SPI by setting the SPE bit to 1:

a) 

In master mode, this immediately activates the generation of the SCK clock, and 
data are serially received until the SPI is disabled (SPE=0).

b) 

In slave mode, data are received when the SPI master device drives NSS low and 
generates the SCK clock.

3. 

Wait until RXNE=1 and read the SPI_DR register to get the received data (this clears 
the RXNE bit). Repeat this operation for each data item to be received.

This procedure can also be implemented using dedicated interrupt subroutines launched at 
each rising edge of the RXNE flag.

Note:

If it is required to disable the SPI after the last transfer, follow the recommendation described 
in 

Section 25.3.8: Disabling the SPI on page 693

.

0xF1

Tx 

bu

ffer

 TXE fl

a

g

0xF2

 B

S

Y fl

a

g

0xF

3

software writes 

0xF1 into 

SPI_DR

software waits 

until TXE=1 and 

writes 0xF2 into 

SPI_DR

s

et 

b

y h

a

rdw

a

re

cle

a

red 

b

y 

s

oftw

a

re

s

et 

b

y h

a

rdw

a

re

cle

a

red 

b

y 

s

oftw

a

re

s

et 

b

y h

a

rdw

a

re

s

et 

b

y h

a

rdw

a

re

S

CK

re

s

et 

b

y h

a

rdw

a

re

Ex

a

mple in 

s

l

a

ve mode with CPOL=1, CPHA=1

(write to 

S

PI_DR)

MI

S

O/MO

S

I (o

u

t)

DATA 1 = 0xF1

DATA 2 = 0xF2

DATA 

3

 = 0xF

3

software waits 

until TXE=1 and 

writes 0xF3 into 

SPI_DR

software waits until BSY=0

software waits until TXE=1 

b

0

b

1

b

2

b3 b

4

b

5

b

6

b

7

b

0

b

1

b

2

b3 b

4

b

5

b

6

b

7

b

0

b

1

b

2

b3 b

4

b

5

b

6

b

7

a

i17

3

46

Summary of Contents for STM32F101xx series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments