ST STM32F101xx series Reference Manual Download Page 111

Page: 111 / 1096

RM0008

Low-, medium-, high- and XL-density reset and clock control (RCC)

Doc ID 13902 Rev 12

111/1096

7.3.8

APB1 peripheral clock enable register (RCC_APB1ENR)

Address: 0x1C

Reset value: 0x0000 0000

Bit 10

ADC2EN:

ADC 2 interface clock enable

Set and cleared by software.
0: ADC 2 interface clock disabled
1: ADC 2 interface clock enabled

Bit 9

ADC1EN:

ADC 1 interface clock enable

Set and cleared by software.
0: ADC 1 interface disabled
1: ADC 1 interface clock enabled

Bit 8

IOPGEN:

IO port G clock enable

Set and cleared by software.
0: IO port G clock disabled
1: IO port G clock enabled

Bit 7

IOPFEN:

IO port F clock enable

Set and cleared by software.
0: IO port F clock disabled
1: IO port F clock enabled

Bit 6

IOPEEN:

IO port E clock enable

Set and cleared by software.
0: IO port E clock disabled
1: IO port E clock enabled

Bit 5

IOPDEN:

IO port D clock enable

Set and cleared by software.
0: IO port D clock disabled
1: IO port D clock enabled

Bit 4

IOPCEN:

IO port C clock enable

Set and cleared by software.
0: IO port C clock disabled
1: IO port C clock enabled

Bit 3

IOPBEN:

IO port B clock enable

Set and cleared by software.
0: IO port B clock disabled
1: IO port B clock enabled

Bit 2

IOPAEN:

IO port A clock enable

Set and cleared by software.
0: IO port A clock disabled
1: IO port A clock enabled

Bit 1 Reserved, always read as 0.

Bit 0

AFIOEN:

Alternate function IO clock enable

Set and cleared by software.
0: Alternate Function IO clock disabled
1: Alternate Function IO clock enabled

Summary of Contents for STM32F101xx series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for STM32F101xx series

Reviews:

ST STM32F101xx series, Reference Manual, Page: 111 / 1096

Search results

Summary of Contents for STM32F101xx series

Reviews: