ST ST7LITEUS2 Quick Start Manual Download Page 77 | Manualshive

Page: 77 / 136

ST ST7LITEUS2 Quick Start Manual Download Page 77

Obsolete Product(s) - Obsolete Product(s)

Obsolete Product(s) - Obsolete Product(s)

ST7LITEUS2, ST7LITEUS5

On-chip peripherals

PWM0 control/status register (PWM0CSR)

Reset value: 0000 0000 (00h)

PWM output control register (PWMCR)

Reset value: 0000 0000 (00h)

7

0

0

0

0

0

0

0

OP0

CMPF0

Read/Write

Bit 7:2 Reserved, must be kept cleared.

Bit 1

OP0

PWM0 output polarity.

This bit is read/write by software and cleared by hardware after a reset. This bit
selects the polarity of the PWM0 signal.
0: The PWM0 signal is not inverted.
1: The PWM0 signal is inverted.

Bit 0

CMPF0

PWM0

Compare Flag.

This bit is set by hardware and cleared by software by reading the PWM0CSR
register. It indicates that the upcounter value matches the DCR0 register value.
0: Upcounter value does not match DCR value.
1: Upcounter value matches DCR value.

7

0

0

0

0

0

0

0

0

OE0

Read/Write

Bits 7:1 Reserved, must be kept cleared.

Bit 0

OE0

PWM0 Output enable

.

This bit is set and cleared by software.

0: PWM0 output Alternate Function disabled (I/O pin free for general purpose I/O)

1: PWM0 output enabled

Table 30.

Register map and reset values

Address

(Hex.)

Register

label

7

6

5

4

3

2

1

0

0D

ATCSR

Reset value

0

0

0

CK1

0

CK0

0

OVF

0

OVFIE

0

CMPIE

0

0E

CNTRH

Reset value

0

0

0

0

CN11

0

CN10

0

CN9

0

CN8

0

0F

CNTRL

Reset value

CN7

0

CN6

0

CN5

0

CN4

0

CN3

0

CN2

0

CN1

0

CN0

0

10

ATRH

Reset value

0

0

0

0

ATR11

0

ATR10

0

ATR9

0

ATR8

0

Obsolete Product(s) - Obsolete Product(s)

«
...
75
76
77
78
79
...
»

Summary of Contents for ST7LITEUS2









































































































































Reviews:

No comments