ST SPWF04S Series User Manual Download Page 49

Page: 49 / 66

Table 9.

Peer variables

Peers variables

Value

Note

AT-S.Var:n.<var> where n:0=mode connected to STA; n between 1 to 5=id of the connected client

link_id

Identifier of the client

state

0 = Hardware Power Up

1 = HW link initialization

2 = Client Link identifier allocated

3 = Authenticated

4 = Associated

5 = Peer lost beacons

6 = Peer in power save state

addr

02:62:1F:51:8F:0B

MAC address of the client

last_rx

Timestamp of last received packet

last_tx

Timestamp of last transmitted packet

rx_drops

Count of frames dropped during reception

tx_drops

Count of frames dropped during transmission

rx_pkts

Count of received frames

tx_pkts

Count of transmitted frames

tx_errs

Count of errors detected during frame transmit

rate_mask

0x00003FCF

AP reported Operational data rate mask

cur_rate_idx

Most significant byte of the rate_mask

cur_rate_ok

Counter to perform rate step up

cur_rate_fail

Counter to perform rate step down

tx_consec_fail

Counter to perform disassociation

rx_seqnum

0x000031F0

Sequence number of last RX directed frame

rx_seqnum_mc

0x00002780

Sequence number of last RX multicast frame

rx_rssi

-51

Signal strength of last received packet

rx_rateidx

Rate index of last received packet

setprot

Bitmask to indicate protection for TX (bit 1) and/or RX (bit 0) IEEE 802.11 frames

listen_interval

AP reported listen interval

capinfo

0x00000411

Information about the AP capabilities

UM2114

Variables and values

UM2114

Rev 3

page 49/66

Summary of Contents for SPWF04S Series



































































Search results

Summary of Contents for SPWF04S Series

Reviews:

Related manuals for SPWF04S Series

Brands by name

Popular brands

ST SPWF04S Series, User Manual

Search results

Summary of Contents for SPWF04S Series

Reviews:

Related manuals for SPWF04S Series

Brands by name

Popular brands