manualshive.com logo in svg

ST MB1361, User Manual, Page: 40 / 48

Share
Download
ST MB1361 User Manual Download Page 40

8

Limitation

8.1

RSS/bootloader limitation

Issue observed:

The STM32L5 part soldered on NUCLEO-L552ZE-Q that embeds the bootloader V9.0 is affected by the
limitations described in 

Section  6.11  RSS/bootloader

.

Proposed workaround:

Refer to 

Section  6.11  RSS/bootloader

 to detail workaround.

Parts impacted:

This applies only to the NUCLEO-L552ZE-Q with the finished good (FG) 

NUL552ZEQ$AU1

 (Sticker available on

the top side of the board).

8.2

SMPS limitation

Issue observed:

The STM32L5 part soldered on NUCLEO-L552ZE-Q embeds an internal SMPS. The sample revision rev B
embeds two SMPS limitations: 

SMPS regulation loss upon transiting into SMPS LP mode

, and

Unpredictable SMPS state at power-on

. Refer to errata sheet 

STM32L552xx/562xx device errata

 (ES0448) for

more details.

Proposed workaround:

Refer to errata sheet 

STM32L552xx/562xx device errata

 (ES0448).

Parts impacted:

This applies only on the NUCLEO-L552ZE-Q with the finished good (FG) 

NUL552ZEQ$AU1

 (Sticker available on

the top side of the board).

UM2581

Limitation

UM2581

 - 

Rev 2

page 40/48

Summary of Contents for MB1361

















































Reviews:

No comments