manualshive.com logo in svg

ST EVALSP1310CPU, User Manual, Page: 28 / 36

Share
Download
ST EVALSP1310CPU User Manual Download Page 28

Jumper descriptions

UM1585

28/36

Doc ID 023872 Rev 1

13 Jumper 

descriptions 

The board has the following jumpers for settings or measurements:

         

Table 23.

List of board jumpers

Jumper

Description

J23 (4) 

M25P64 (U1) nCS select (default 1-2 closed: 3-4 closed)

JP1 (3)

SAFHV antifuse (OTP) cell power supply VDD2V5 (default closed 1-2)

JP2 (3)

NAND FLASH VDD (default 1-2 closed = 3.3 V) 

JP3 (3)

NAND FLASH SPEAr I/O (default 1-2 closed = 3.3 V)

JP4 (2)

On-board NAND FLASH (U4) closed = enabled

JP5 (3)

MIPHY (U5) VDD_IO (default 1-2 closed = 3.3 V)

JP6 - JP11 (3+3) 

GIGA PHY STRAP13

JP7 - JP12 (3+3)

GIGA PHY STRAP10

JP8 - JP13 (3+3) 

GIGA PHY STRAP9

JP9 - JP14 (3+3) 

GIGA PHY STRAP8

JP10 - JP15 (3+3)

GIGA PHY STRAP7

JP16 (3)

SPEAr GMII I/F VDD (default 1-2 closed = 3.3 V)

JP17 (3) 

GMII_COL. (default 1-2 closed = pull up)

JP18 (3)

MII_TXCLK_SEL1 (default 2-3 closed)

JP19 (3) 

CRS_RGMII_SEL0 (default 2-3 closed)

JP23 (2) 

Power OFF LM2731 (U7) (default open) 

JP24 (2) 

Connect SPEAr_VDD2V5 to MIPHY_VDD2V5_PLL (default open)

JP27 (3) 

MIPHY_VDD1V2 (default 1-2 closed)

JP28 (3) 

A2D_PLL_VDD2.5 (default 1-2 closed = internal regulator)

JP29 (3) 

USB_VDD2V5. (default 1-2closed = internal regulator)

JP30 (2) 

SPEAr_DDR3_1V2 (default closed)

JP31 (2) 

SPEAr_VDD1V2 (default closed)

JP32 (2) 

SPEAr_DDR3_1V5 (default closed)

JP33 (2) 

SPEAr_VDD2V5 (default closed)

JP34 (2) 

SPEAr_VDD3V3 (default closed)

JP37 (2) 

SS_nINH, Power off L5989 (U21) (default open)

JP39 (2) 

RTC_VDD1V5 (default closed)

JP42

GIG PHY Ethernet power selection (default 1-2 closed = 3.3 V)

JP44 (3)

RTC Power Selection (default 1-2 closed)

Summary of Contents for EVALSP1310CPU





































Reviews:

No comments