SST Automation GT200-HT-RS User Manual Download Page 19 | Manualshive

Page: 19 / 52

background image

WWW.SSTCOMM.COM

19

4 Software Instructions

4.1 Software Interface Description

SST-HT-CFG is configuring software based on Windows platform, and used to configure HART series

products.

The following describes how to use the software SST-HT-CFG to configure the product GT200-HT-RS. You

may also check the software user manual to get detailed usage.

Double-click on the icon

to enter the main interface of software:

Tool Bar:

Toolbar interface shown as follow:

Network Settings interface:
Contains Fieldbus and the
connection object

Menu Bar

Tool Bar

Parameter Settings interface:
Contains

modifiable

part

(white) and unmodifiable part
(grey)

Comment field: Explain
the

function

of

the

configuration options

«
...
17
18
19
20
21
...
»

Summary of Contents for GT200-HT-RS





















































Reviews:

No comments

Related manuals for GT200-HT-RS

Brand: QTS Pages: 62

Brand: XAVI Technologies Corp. Pages: 51

Brand: SVS Pages: 4

Brand: Top Global Pages: 75

IGW1111-3IN1-DB

Brand: 3onedata Pages: 3

Brand: Yeastar Technology Pages: 14

Brand: Advantech Pages: 74

KoolKey EKA 200

Brand: Danfoss Pages: 2

Brand: Matrix Pages: 322

Brand: Dialogic Pages: 11

NetLink Wireless Telephone

Brand: SpectraLink Pages: 30

lpnGate LoRaWAN

Brand: LPN Plant Pages: 20

Brand: Hewlett Packard Enterprise Pages: 26

HomePortal 3700HGV

Brand: 2Wire Pages: 4

MediaAccess TG589vn

Brand: Technicolor Pages: 106

Brand: ICPDAS Pages: 52

Brand: Rosslare Pages: 28

Brand: Rosslare Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands