SSBC W123-3ADS Installation Instructions Manual Download Page 1

INSTALLATION INSTRUCTIONS

PEROFRMANCE AT THE WHEELS KITS 

W123-ADS, W123-3ADS

1964 - 72 A-BODY

1967 - 69 F-BODY

1968 - 74 X-BODY

_____________________________________________________________________

Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking

needs. Please take the time to read and carefully follow these instructions to insure the ease of your
installation as well as the proper performance of the complete system.

Before beginning your installation, please verify you have received all the parts indicated on

the packing slip. If you believe anything to be missing or incorrect, please call our Customer Service
Department at 716-759-8666.

To assure your installation will go safely and smoothly, have the following items on hand to

assist you:

JACK & JACK STANDS

WRENCH SET

LUG WRENCH

TUBE WRENCHES

TORQUE WRENCH

MALLET

SOCKET SET

WHEEL BEARING GREASE

BRAKE CLEANER

BRAKE FLUID

Stainless Steel Brakes Corporation • 11470 Main Road • Clarence, NY  14031

Phone: (800) 448-7722 • (716) 759-8666 • Fax: (716) 759-8688

www.ssbrakes.com • [email protected]

Revised to level 3 4/17/12

These kits use the following pads:

SSBC#:

1015

FMSI#:

D-52

Summary of Contents for W123-3ADS











Reviews: