manualshive.com logo in svg

SRAM RockShox Super Deluxe Flight Attendant, User Manual, Page: 38 / 41

Share
Download
SRAM RockShox Super Deluxe Flight Attendant User Manual Download Page 38

38

1

2

3

4

0.56 N·m

(5 in-lb)

Install the Pedal Sensor into the non-drive 

side crank spindle. 

While pressing the end of the Pedal Sensor 

into the crank with your thumb, tighten 

the expander wedge bolt to the specified 

torque.

NOTICE

To avoid damage to the expander wedge, 

do not over tighten the expander wedge 

bolt.

Adjust

Install

Torque

Non-Threaded Pedal Sensor - Installation

Threaded Pedal Sensor - Installation

1

2

Install the Pedal Sensor into the non-drive 

side crank spindle. 

Thread the Pedal Sensor into the crank until 

it is hand tight.

NOTICE

To avoid damage to the seal tube, do not 

over tighten. Confirm the crank is flush 

against the bottom bracket and that there 

is no side to side movement.

Tighten the expander wedge bolt to the specified torque.

NOTICE

To avoid damage to the expander wedge, do not over tighten the 

expander wedge bolt.

Tighten the crank pinch bolts to the crank manufacturer's torque 

specification.

NOTICE

To avoid damage to the crank arm, do not over tighten the pinch 

bolts.

4

5

3

4

0.56 N·m

(5 in-lb)

Summary of Contents for RockShox Super Deluxe Flight Attendant










































Reviews:

No comments