manualshive.com logo in svg

SRAM RockShox Super Deluxe Flight Attendant, User Manual, Page: 35 / 41

Share
Download
SRAM RockShox Super Deluxe Flight Attendant User Manual Download Page 35

35

Pedal Sensor - Battery and Service

NOTICE

To avoid permanent damage to the Pedal Sensor caused by battery corrosion, ONLY use AAA Lithium/Iron Disulfide (Li/FeS

2

)  

non-rechargeable batteries. 
Do NOT use rechargeable Lithium (Li-ion), alkaline, or nickel metal hydride (Ni-MH) batteries in the Pedal Sensor.

2

3

1

4

Loosen the Pedal Sensor bolt (drive side) while pushing the Pedal 

Sensor assembly into the crank spindle. When the expander wedge 

is loose enough, push the Pedal Sensor assembly out of the  

non-drive side crank spindle with the hex wrench.

NOTICE

Only loosen the expander wedge bolt enough to dislodge the 

wedge; do not remove the bolt.

Non-Threaded Pedal Sensor - Removal

Threaded Pedal Sensor - Removal

1

4

Loosen the Pedal Sensor expander wedge bolt (drive side).

NOTICE

Only loosen the expander wedge bolt enough to dislodge the 

wedge; do not remove the bolt.

Remove/Loosen

Adjust

4

2

5

3

Threaded Seal Tube:

 Loosen the crank arm pinch bolts.

NOTICE

Only loosen the pinch bolts; do not remove.

Unthread the Pedal Sensor from the non-drive side crank arm and 

spindle. 
Remove the Pedal Sensor from the crank spindle.

Summary of Contents for RockShox Super Deluxe Flight Attendant










































Reviews:

No comments