manualshive.com logo in svg

SRAM RockShox Super Deluxe Flight Attendant, User Manual, Page: 12 / 41

Share
Download
SRAM RockShox Super Deluxe Flight Attendant User Manual Download Page 12

12

2

4

3

1

SRAM Battery Charging

Suspension Module Battery Installation

NOTICE

Do not discard the battery covers (A) and component battery 

blocks (B).
To prevent battery depletion during transportation, remove the 

SRAM batteries and install the battery blocks into each battery 

slot. Install each battery cover onto each battery. 
Failure to cover the batteries and component battery terminals 

could result in damage to the terminals.

A

B

Remove the battery cover from each SRAM battery and charge both 

batteries.
Consult the 

SRAM Battery and Charger User Manual

 at  

www.sram.com/service

 for charging instructions, battery 

maintenance, and travel guidelines.

NOTICE

Do not discard the battery cover. To protect the battery terminals, 

install the battery cover on the battery when it is not on the 

charger or component.

Adjust

Remove/Loosen

Install

1

2

1

2

Open the battery latch and remove the battery block.

NOTICE

The battery block is installed to protect the electronic terminals.

Summary of Contents for RockShox Super Deluxe Flight Attendant










































Reviews:

No comments