background image

Model SR7020

i

 Wall Mount Platform Scale 

Operating and Service Manual  
Part No.MAN7020I_MICROBAN_200520 

 

Page 14 of 16 

 

S

Instruments, Inc.

600 Young Street, Tonawanda, NY  14150 

Tel:  716-693-5977     Fax:  716-693-5854    URL:  

www.srscales.com

 

email:  

[email protected]

       Copyright 2020

 

S

Instruments, Inc. 

TROUBLESHOOTING 

 

 

SYMPTOM 

REASON/CORRECTIVE ACTION 

The characters only appear on half of the 
display. 

Press the

 “WEIGH” 

button or disconnect power. Wait 

five seconds, then re-connect the power and try the 

“WEIGH” 

button again.

 

 

The display lights appear to work, but do not 
respond to button activation. 

Check  to  ensure  the  membrane  switch  label  is  correctly 
plugged into display board. 

Check  to  ensure  the  calibration  switch  is  not  in  the 
Calibration Mode (Figure 6). 

 

The display shows no reading at all. 

Check that power supply is plugged in. Check display cable 
to make sure it is connected securely. 

 

For additional information or assistance, telephone our Service Hotline: 1-800-654-6360 

or e-mail: 

[email protected]

 

Summary of Contents for SR Scales SR7020i

















Reviews: