background image

 
  
 

November 15,2018  

 

 

11 

301-147 8’ WHEELCHAIR ACCESSIBLE MGR 

INSTALLATION INSTRUCTION 

 

__9.  There are two types of handrails, a left and right. Ensure 
that the sleeve for the left handrail and sleeve for the right are 
pointed at each other so you can install the gates properly as 
shown by the arrows to the left 
__10. Attach the Handrails (2 & 19) to the Deck Sections (1) 
using 1 1/4” bolts, one 3/8 washer  (Detail f shows a nut under 
the deck, however this unit has factory installed nuts). It is easier 
to attach and leave loose until after you have attached the upper 
handrail. 
__11.  Once all four handrails have been positioned, attach the 
Upper Handrail (22) to the four handrails using two T-clamps at 
each location and securing in position by inserting a 5/16” x 1 
1/2” Button Head bolt through a 5/16” flat washer a T-clamp the 
handrail, another T-clamp and into a %/16” x 1” button head not. 
When the T-clamp is in position on the main handrail, tighten 
bolts. Repeat at all four main handrail and upper handrail 
connection points. 
__12.  

Governor Tension Adjustment

: Back off the jamb nut 

on the governor assembly (attached to post assembly) and turn 
the adjustment nut until the rubber wheel is pushing firmly onto 
the sleeve of the hub assembly.  Once wheel is firmly against the 
hub, tighten the jamb nut to secure it into position. (See Detail B)  

 

 

 

 

Summary of Contents for 301-147

















Reviews: