background image

Page

features

ASSEMBLY INSTRUCTIONS

Check out our website for more information about other exciting sport flyers products!

WWW.hobbypeople.net

Wing span top and bottom:  

30 Inches (762mm)

  

l

  

Wing area:

  350 Square Inches (22.6dm

2

)  

l

 

 

length:

  33 Inches (838mm)

Weight rtf:

  13 Ounces (369gr)  

l

  

Wing loading:

  5.5 Ounces/Square Foot (156gr/dm

2

)  

l

  

functions:

  Elevator, Rudder, Throttle and Ailerons

radio required:

  4-Channel or More w/3 Micro Servos and Micro Rx  

l

  

Motor required:

  KMS 2208/26 Brushless Outrunner Motor

esC required:

  KMS 18 Amp Brushless  

l

  

battery required:  

Impulse Power 3 Cell 900mAH LiPO

  l

  Factory-Cut and -Printed Foam Parts

 

l

  Full-Shape Fuselage with Foam Stiffeners and Sheet-Foam Elliptical Wings

 

l

  Carbon Fiber Stiffeners for Great Strength

 

l

  Carbon Fiber Landing Gear with Lightweight Wheels and Wheel Covers

 

l

  Accepts a Wide Range of Outrunner Brushless Motors and Micro Radio Equipment

 

l

  Different Color Scheme on Top and Bottom Presents Well During Maneuvers

 

l

  Great Flying Characteristics

 

l

  Includes all Necessary Hardware

 

l

  Fast and Easy Assembly - 60 High-Resolution Digital Photos to Guide You

Made in China

Kit product number  160532

The Sport Flyers Rhythm 3D EP Biplane is sold exclusively

in the USA by Hobby People

18480 Bandilier Circle, Fountain Valley, CA  92708

Copyright © 2006, Hobby People - All Rights Reserved

Version 1.0  March 2007

speCifiCations

Celebrating 35 years serving modelers the world over, Hobby People wanted to bring their customers a top-performing 3D foamy 
that was light, versatile, fun, and affordable.  A nice model to celebrate 35 years of making planes for the real champions, those who 

fly for fun!

Working with aeronautical engineers and modelers from around the world, Hobby People presents the Rhythm. The Rhythm is as 
neutral and as uncoupled as we could ever hope for in a foamie bipe.  Almost zero roll-coupling, and almost zero compensation 

needed for inverted and knife edge flight, the Rhythm is amazingly smooth throughout the flight envelope.  You'll notice amazing 

rudder response, yet with properly set up control throws and exponential, the Rhythm is smooth and "honest".  Indeed, it is fun and 

the Sport Flyer is going to love flying the Rhythm.

Summary of Contents for Sport Flyers Rhythm 3D EP

























Reviews: