Splicecom 4100 Installation & Maintenance Manual Download Page 287

Page: 287 / 374

Installation and Maintenance Manual

Maintenance & Troubleshooting

Installation and Maintenance Manual v4/0615/10

283

The SpliceCom LED will turn off for a maximum of 10 seconds while the file system closes

The LED will then flash slowly to indicate that the shut down is complete.

At this point the power can be removed.

Please note that the SpliceCom LED will flash for 60 seconds and then the Call Server will automatically

reboot.

The above procedure can be performed on a Phone and Trunk Module before power down, however as

neither module contains a hard disk this procedure is not essential.

Rebooting a module

A reboot may be required on a module in order to restore connection to the LAN, restore connection to

the Call Server etc.

On the relevant module press the Reset Switch once.

The SpliceCom LED will turn off for a maximum of 10 seconds

The LED will then flash slowly to indicate that the shut down is complete.

Press the Reset Switch once (or no more than 3 times).

wait for 60 seconds the module will automatically restart.

The LED will turn off for 10 seconds and then become solid one the unit is back up.

Backing up the Database

A regular back up of the configuration of the system should be made in order to be able to restore a

system quickly and easily if, for example, an error is made in the configuration and you wish to return to a

previous configuration or a faulty Call Server is replaced.

Please note: remember to also back up any WAV files or .csv files stored in the ftp directory, and to back

up the internal voicemail server (as described in the Troubleshooting Voicemail section from page 261)

and web pages (as described in the Internal Web Server section from page 264).

Creating a back-up of the configuration

In Manager Assist, select System Utilities

Select Backup Config

A backup of the current configuration of the database will be made and stored within the /ftp

directory of the Call Server. The name of the file created is displayed on the screen.

You can then download a copy of this file to an external location, such as your desktop, network

folder and so on, by selecting the Download link

Please note:

A back up is also created each time the Call Server is rebooted.

A copy of the backup file must be made before a Factory Restart, as this file will be deleted.

Summary of Contents for 4100























































































































































































































































































































































































Search results

Summary of Contents for 4100

Reviews:

Brands by name

Popular brands

Splicecom 4100, Installation & Maintenance Manual

Search results

Summary of Contents for 4100

Reviews:

Brands by name

Popular brands