I N S T A L L A T I O N M A N U A L
www.spitzerlighting.com
702 Interchange Blvd., Newark, DE 19711 • Toll Free: 844-312-4574
Specification is subject to change without notice
1/2
LED WALL SCONCE
WS15W3K
S A F E T Y I N F O R M A T I O N
S A F E T Y I N F O R M A T I O N
PACKAGE CONTENTS
DIMMING COMPATIBLE CONTROLS
C A U T I O N :
P R E - I N S T A L L A T I O N
PLEASE READ AND UNDERSTAND THIS ENTIRE MANUAL BEFORE ATTEMPTING TO ASSEMBLE,
OPERATE OR INSTALL THE PRODUCT.
• Turn off electricity at main fuse box (or circuit breaker box) before beginning installation by removing fuse or switching off
circuit breaker.
• Be careful not to damage or cut the wire insulation (covering) during fixture installation. Do not permit wires to contact any
surface having a sharp edge. To do so may damage or cut the wire insulation, which could cause serious injury or death from
electric shock.
• LED electronics can be damaged by electro static discharge (ESD) shock. Before installation, discharge yourself by touching a
grounded bare metal surface to remove this hazard. To avoid damage, do not touch the LED module.
• All electrical connections must be in agreement with local codes, ordinances or the national electric code (NEC).
• Contact your municipal building department to learn about your local codes, permits and/or inspections.
•
RISK OF FIRE
– most dwellings built before 1985 have supply wire rated for 140°F/60ºC.Consult a qualified electrician before
installation.
• Do not connect this fixture to an electrical system that does not provide a means for equipment grounding. Never use a fixture
in a two-wire system that is not grounded. If you are not sure your lighting system has a grounding means, do not attempt to
install this fixture. Contact a qualified, licensed electrician for information with regards to proper grounding methods as required
by the local electrical code in your area.
• If a dimmer control switch is used with this fixture, obtain professional advice to determine the correct type and electrical rating
required.
STEP 1
Use 2 pieces of umbrella head screws in the accessory bag to fix the
installation plate onto the junction box;
• BEFORE BEGINNING ASSEMBLY, INSTALLATION OR OPERATION OF PRODUCT, MAKE SURE ALL PARTS ARE PRESENT.
COMPARE PARTS WITH PACKAGE CONTENTS LIST AND DIAGRAM ON PREVIOUS PAGE. IF ANY PART IS MISSING OR
DAMAGED, DO NOT ATTEMPT TO ASSEMBLE, INSTALL OR OPERATE THE PRODUCT. CONTACT CUSTOMER SERVICE FOR
REPLACEMENT PARTS.
• TOOLS REQUIRED FOR ASSEMBLY (NOT INCLUDED): SCREWDRIVER, PHILLIPS SCREWDRIVER, PLIERS, ELECTRICAL TAPE,
WIRE CUTTERS, SAFETY GLASSES, LADDER, WIRE STRIPPER.
• NON-REPLACEABLE LED’S.
• IF YOU ARE NOT FAMILIAR WITH THE STATE AND LOCAL CODES, IT IS RECOMMENDED THAT YOU CONSULT WITH A QUALIFIED ELECTRICIAN.
• SUITABLE FOR DAMP LOCATION, USE INDOORS ONLY.
• CAUTION: LED’S EMITS BRIGHT LIGHT. AVOID LOOKING DIRECTLY INTO THE LIGHT SOURCE FOR LONG PERIODS TO AVOID EYE DAMAGE.
• DIMMABLE (SOLD SEPARATELY).
• 120V FOR RESIDENTIAL USE.
INSTALLATION
ASSEMBLY INSTRUCTIONS
PART
DESCRIPTION
QTY
--
LED Wall Sconce Fixture
1
A
Mounting bracket
1
B
Mounting Screws
2
C
Outlet box screws
2
D
Wire nuts
3
LUTRON
LEVITON
SCL-153P
IPM10-1LZ
TGCL-153P
DV-603P
PD-6WCL
MACL-153M
AY-600P
( TO AVOID RISK OF ELECTRIC SHOCK, MAKE SURE TO TURN OFF MAIN POWER SWITCH PRIOR TO INSTALLATION OR MAINTENANCE)
STEP 1
