SpeedTech Lights RAPTOR-X Instruction Manual Download Page 7

Page: 7 / 13

RAPTOR

-X

VISOR LIGHT BAR

Q-3070 Universal Mounting Bracket Installation

Base Bracket and Q-3070 Universal Visor Bracket Assembly

To attach the base bracket and visor bracket, you will need the following for each of the (4) assemblies:

• (2) Phillips pan head screws

• (4) Flat washers

• (2) Split lock washers

• (2) Hex nuts

Note: The Universal Visor Bracket comes with (2) sets of forked visor

brackets. Choose the length of fork that will work best to fit your vehicle.

1. Take both brackets and overlap the openings.

2. Insert (2) Phillips pan head screws through the base

bracket opening.

3. On the other end, insert (2) flat washers, (2) split lock

washers, and (2) hex nuts to secure.

NOTE: Do not fully tighten at this point as adjusting

will need to be done.

4. Repeat Steps 1 - 3 for each assembly. There will be a

total of (4) assemblies.

Summary of Contents for RAPTOR-X














Search results

Summary of Contents for RAPTOR-X

Reviews:

Related manuals for RAPTOR-X

Brands by name

Popular brands

SpeedTech Lights RAPTOR-X, Instruction Manual

Search results

Summary of Contents for RAPTOR-X

Reviews:

Related manuals for RAPTOR-X

Brands by name

Popular brands