background image

4

SpeedTech Lights, Inc © 2019 

RAPTOR

®

-X

VISOR LIGHT BAR

Specifications

Voltage

12 VDC

Amps

< 4.2

Optic

TIR / Linear

LED Count

TIR: 32 / Linear: 32

Cable Length

11’ Light Bar Cable, 1.5’ Cig Plug Cable (Sold Separately)

Cable Length Between Each Side

2.5’

Flash Patterns

23

Wiring Diagram

Wire Color

Function

 Red*

Positive

 Black*

Negative

 Yellow

Flash Pattern

* Indicates a main power cable.                                                                                                  NOTE: All cables except Negative c12 VDC.

Cigarette Lighter Plug Switch Operation (Sold Separately)

On/Off Switch:

• 

On Position: Turns on the Light Bar.

• 

Off Position: Turns off the Light Bar.

Flash Pattern Button:

• 

Cycles to the next flash pattern with each press.

• 

Non-Volatile memory recalls the last flash pattern selected.

• 

Hold for 3 seconds to toggle Steady Burn mode.

• 

Hold for 5 seconds to toggle Random pattern mode.

Extension Cable (Sold Separately)

• 

If you have an extension cable with connectors, connect the corresponding ends to one 

another. Use the connector at the end of the cable to plug into the control box.

• 

If you have an extension cable with one connector, you will need to cut the connector off 

of the main cable harness coming out of the Light Bar. Save it as a spare part. You will 

solder and heat shrink each wire within the cable harness to each wire in the extension 

cable harness. DO NOT cross connect wires. Use the connector at the end of the 

extension cable to plug into the control box.

• 

If you have an extension cable with no connectors, you will need to cut in the middle 

of the main cable harness coming out of the Light Bar. You will solder and heat shrink 

each wire within the cable harness to each wire in the extension cable harness. DO 

NOT cross connect wires. Use the reattached connector from the end of the main cable 

harness to plug into the control box.

• 

NOTE: DO NOT leave connectors, cables, solder points exposed to heat, moisture, or 

debris.

Summary of Contents for RAPTOR-X














Reviews: