manualshive.com logo in svg

SpectraLink TGA108, Installation, Configuration And Administration, Page: 15 / 82

Share
Download
SpectraLink TGA108 Installation, Configuration And Administration Download Page 15

SpectraLink Corporation 

Installation, Configuration, and Administration  

 

NetLink Telephony Gateway  

Part Number: 72-0065-02-R.doc 

Page 15 

4.2

 

LAN Requirements 

Network Infrastructure 

The NetLink Telephony Gateway connects to your local area network (LAN). To 
provide adequate bandwidth and limit collisions, an Ethernet switch is required. The 
traffic between the NetLink Telephony Gateway and wireless LAN APs should be 
isolated as much as possible to avoid additional latency. The NetLink Telephony 
Gateway and APs must be on the same logical IP subnet. Inter-subnet roaming is 
not permitted for wireless devices. 
Each NetLink Telephony Gateway to be installed requires a 10 Mb/s switched 
Ethernet connection. 
The NetLink Telephony Gateway and wireless telephones rely on wireless LAN APs 
to transmit and receive packets from wireless telephone devices. The APs must be 
compatible with the IEEE 802.11 standard for wireless LANs, either frequency 
hopping or direct sequence spread spectrum radios. To configure a wireless LAN to 
support NetLink Telephony Gateways and wireless telephones refer to 

Deploying 

NetLink Wireless Telephones: Best Practices

. 

IP Addressing 

The NetLink Telephony Gateway, along with each of the handsets associated with it, 
requires an IP address. The system administrator must determine what IP addresses 
are to be used by the NetLink Telephony Gateway and APs. Handsets can be 
configured to use DHCP or Static IP addressing. Record IP address assignments on 
the 

Wireless Device Planning Worksheet

s—one for each NetLink Telephony Gateway. 

These worksheets may be started when the system is installed. The information 
recorded on them is used in the configuration and continuing administration of the 
system. 

 

IP multicast addresses are used by the NetLink i640 Wireless Telephone. 
This requires that multicasting be enabled on the subnet used for the 
NetLink Wireless Telephones, SVP Server, and Telephony Gateways. 
Routers are typically configured with filters to prevent multicast traffic 
from flowing outside of specific domains. The wireless LAN can be placed 
on a separate VLAN or subnet to reduce the effects of broadcast and 
multicast traffic from devices in other network segments. 

 

Summary of Contents for TGA108



















































































Reviews:

No comments