Home
/
SpectraLink
/
8440
/
Administration Manual

SpectraLink 8440, Administration Manual

Share

Page: 305 / 335

SpectraLink 8440 Administration Manual Download Page 305

Spectralink 84-Series Series Wireless Telephones Administration Guide

1725-86984-000_P.docx
September 2016

305

Note: Using the Answer Ring Type

The auto-answer on incoming call is currently only applied if there is no other call in
progress on the handset at the time.

Note: Silent Ring

Silent ring will provide a visual indication of an incoming call, but no audio
indication.

Sampled audio files 1 to 10 all use the same built-in file unless that file has been
replaced with a downloaded file.

Ring Tones <rt/>

Ringtone is used to define a simple class of ring to be applied based on some credentials that
are usually carried within the network protocol. The ring class includes parameters such as call-
waiting and ringer index, if appropriate. The ring class can use one of four types of ring that are
defined as follows:

ring

Play a specified ring pattern or call waiting indication

visual

Provide only a visual indication (no audio) of an incoming call, no ringer needs to be

specified

answer

Provide auto-answer on an incoming call

ring-answer

Provide auto-answer on an incoming call after a certain number of rings

The handset supports the following ring classes:

default

,

visual

,

answerMute

,

autoAnswer

,

ringAnswerMute

,

ringAutoAnswer

,

internal

,

external

,

emergency

,

precedence

,

splash

,

and

custom<y>

where y is 1 to 17.

In the following table, x is the ring class name.

Sound Effects Ringtone Parameters

Parameter

Permitted Values

se.rt.enabled

0 or 1 (default)

If

0,

the ringtone feature is not enabled on the handset. If

1

(default), the ringtone feature is enabled.

se.rt.modification.enabled

0 or 1 (default)

A flag to determine whether or not to allow user modification (through handset

’s user interface) of the pre-defined

ringtone enabled for modification.

se.rt.<ringClass>.callWait

callWaiting, callWaitingLong,
precedenceCallWaiting

The call waiting tone to be used for this class of ring. The call waiting should match one defined in Table 14-591:
Call Progress Tone Pattern Names. The default call waiting tone is

callWaiting

.

se.rt.<ringClass>.name

UTF-8 encoded string

The answer mode for a ringtone. Used for identification purposes in the user interface.

«
...
303
304
305
306
307
...
»

Summary of Contents for 8440
















































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands