manualshive.com logo in svg

SpectraLink 8440, Administration Manual

Share
Download
SpectraLink 8440 Administration Manual Download Page 182

Spectralink 84-Series Series Wireless Telephones Administration Guide 

1725-86984-000_P.docx 
September 2016 

182 

<oai/> 

The Spectralink handsets support communications using the Open Application Interface (OAI). 
Also see 

Open Application Interface

.You can set the connection parameters using the table 

shown next: 

Table 8-60: Open Application Interface (OAI) Parameters 

Parameter 

Permitted values 

Default 

oai.gateway.address

 

IP address

 

Null

 

The address of the OAI server.

 

oai.userId

 

String of eight hexadecimal characters

 

Null

 

The lower four bytes of the six-byte OAI handset identifier in the OAI gateway. 
If the value is null or invalid, the handset identifies itself to the OAI gateway using the MAC address of the handset; 
otherwise, the upper two bytes are zero and the lower four bytes are as specified. 

 

Summary of Contents for 8440
















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands