manualshive.com logo in svg

SpectraLink 8440, Administration Manual

Share
Download
SpectraLink 8440 Administration Manual Download Page 172

Spectralink 84-Series Series Wireless Telephones Administration Guide 

1725-86984-000_P.docx 
September 2016 

172 

Example Voicemail Configuration 

The following illustration shows you how to enable one-touch access to the voicemail server. In 
the next illustration, line 2 is configured to subscribe to the voicemail server at 

voicemail.Spectralink.com

. 

 

<voIpProt/> 

VoIP Protocol settings are used in wireless environments but may be overruled by <reg

>

 

parameters. You can use VoIP Protocol parameters to set up the call server and DTMF 
signaling. 

 

 

Settings: many voIpProt settings are overruled by counterpart reg.x settings 

Many voIpProt parameters have been replaced by reg.x parameters which will 
overrule their counterpart voIpProt parameters if both are set. We recommend 
using reg.x parameters whenever possible. Some but not all voIpProt parameters 
have replacement reg.x parameters noted in their parameter descriptions. 

 

Table 8-54: VoIP Server Parameters 

Parameter 

Permitted Values 

Default 

voIpProt.server.dhcp.available

1

 

0 or 1

 

0

 

If 0, do not check with the DHCP server for the SIP server IP address. If 1, check with the server for the IP 
address. 

 

Summary of Contents for 8440
















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands