manualshive.com logo in svg

SpectraLink 8440, Administration Manual

Share
Download
SpectraLink 8440 Administration Manual Download Page 156

Spectralink 84-Series Series Wireless Telephones Administration Guide 

1725-86984-000_P.docx 
September 2016 

156 

Parameter 

Permitted Values 

Default 

prov.polling.mode 

abs, rel, random 

abs 

The polling mode.  

abs 

The handset polls every day at the time specified by 

prov.polling.time

.  

rel 

The handset polls after the number of seconds specified by 

prov.polling.period

.

  

random 

The handset polls at random between a starting time set in 

prov.polling.time

 and an end time set 

in 

prov.polling.timeRandomEnd

. Note that if you set the polling period in 

prov.polling.period

 to a time 

greater than 86400 (one day) polling occurs on a random day between the start and end times based on the 
handset

’s MAC address. 

prov.polling.period 

integer> 3600 

86400 

The polling period in seconds. The polling period is rounded up to the nearest number of days in absolute mode. In 
relative mode, the polling period starts once the handset boots. In random mode, if this is set to a time greater than 
86400 (one day) polling occurs on a random day based on the handset

’s MAC address. 

prov.polling.time 

hh:mm 

03:00 

The polling start time. Used in absolute and random modes. 

prov.polling.timeRandomEnd 

hh:mm 

Null 

The polling stop time. Only used in random mode. 

Example Provisional Polling Configuration 

The following illustration shows the default sample random mode configuration for the 
provisional polling feature in the everything.cfg file. 

 

Push-to-talk and Group Paging 

The Push-to-talk (PTT) and Group Paging features are supported on all Spectralink 84-Series 
handset models. 

The Group Paging feature enables pages 

—one-way audio announcements — to users 

subscribed to a page 

group

. Paging mode was originally intended primarily for desktop phones 

but has some use for Wi-Fi handsets that may or may not also be using PTT. In Page mode, 
announcements play only through the handset

’s speakerphone. 

Summary of Contents for 8440
















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands