manualshive.com logo in svg

SpectraLink 8440, Administration Manual

Share
Download
SpectraLink 8440 Administration Manual Download Page 153

Spectralink 84-Series Series Wireless Telephones Administration Guide 

1725-86984-000_P.docx 
September 2016 

153 

 

 

Phone Lock 

The Phone Lock feature allows you to add an option to the Features softkey menu to lock the 
handset and require a password to unlock it. This can be important in certain settings where 
security is an important factor in handset deployment. Keypad lock is available for inadvertent 
key presses. This is a more advanced security feature. 

Please review the 

Enhanced Feature Keys

 section for complete information about configuring 

additional menu keys. Enhanced Feature Keys must be activated to configure this feature. 

When a handset is in a call, IM or OAI session and another call comes in, the handset behaves 
normally and only locks when it returns to the idle state for the configured amount of time. 

A handset may be set to alert when it is locked or it may be set to DND. The following table 
details the different handset behaviors when Alert or DND is turned on. 

Table 8-42: Phone Lock Behavior 

 

Alert 

DND 

Incoming Phone 
call 

Call Alert screen with caller ID info. User 
presses green key and is prompted for user 
PIN, on successful entry call is answered. 
Phone automatically locks on end of call. 

Voice call goes right to voice mail. Phone 
remains locked. 

Incoming OAI 

OAI alert screen (app can put more info on 
screen while 

ringing once ring ack’d). User 

presses green key and is prompted for user 

No OAI alert screen displayed. Phone sends 
“user did not respond to ring” response 
immediately so next level escalation if 

Summary of Contents for 8440
















































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands