manualshive.com logo in svg

Speco N64NR, User Manual, Page: 78 / 114

Share
Download
Speco N64NR User Manual Download Page 78

Alarm Management

NVR User Manual

9.6.5 Push Message

Click   Start

Settings

Alarm

Event   Notification

Push   Message   to   go   to   the   interface   as   shown   below.   Check

“Enable” and then click “Apply” button to save the settings. If Push Server is online, it will push messages to the
mobile clients.  

9.6.6 Alarm Server

Go to Alarm

Alarm Server interface as shown below.

Enable   the   alarm   server   and   enter   server   address   and   port   of   the   alarm   server.   Then   select   protocol.   If   “Send
Heartbeat” is enabled, set the interval times. After that, test the effectiveness of the alarm server. Having tested
successfully, please click “Apply”. When an alarm occurs, the device will transfer the alarm event to the alarm server.
If an alarm server is not needed, there is no need to configure this section.

9.7 Manual Alarm

Click 

 on the tool bar at the bottom of the live view interface to pop up a window. Click “Trigger” to start alarm.

Click “Clear” to stop alarm. 

9.8 View Alarm Status

Click Start

Settings

Alarm

Alarm Status or click 

on the tool bar at the bottom of the live view interfaceto view

the alarm status. 

71

Summary of Contents for N64NR



















































































































Reviews:

No comments