manualshive.com logo in svg

SPACEMAKER RGB108FGEU, Owner'S Manual & Assembly Instructions

Share
Download
SPACEMAKER RGB108FGEU Owner'S Manual & Assembly Instructions Download Page 1

Owner's Manual & Assembly Instructions

 

                                                               Exterior Dimensions                          Interior Dimensions                             Door

                *Approx.                          Base                            (Roof Edge to Roof Edge)                             (Wall to Wall)                                Opening

                      Size                              Size                           Width          Depth       Height             Width        Depth      Height             Width       Height      

 

                   10' x 8'                  121" x 92 3/4"                123 1/4"      95 1/4"      82 1/8"           118 1/4"         90"        80 7/8"            55 1/2"      69 1/4"       

  Storage Area:   74 Sq. Ft.     470 Cu. Ft.

 

                6,9 m

2

           13,3 m

3

BUILDING DIMENSIONS  * Size rounded off  to the nearest foot

CAUTION: SOME PARTS HAVE SHARP EDGES. CARE

MUST BE TAKEN WHEN HANDLING THE VARIOUS PIECES

TO AVOID A MISHAP. FOR SAFETY SAKE, PLEASE READ

SAFETY INFORMATION PROVIDED IN THIS MANUAL

BEFORE BEGINNING CONSTRUCTION. WEAR GLOVES

WHEN HANDLING METAL PARTS.

728220319

      3,0 m x 2,4 m          307,3 cm x 235,6 cm            313,1 cm     241,9 cm    208,6 cm             300,4 cm    228,6 cm   205,4 cm            141,0 cm    175,9 cm

JC01

Model No. RGB108ONEU

RGB108FGEU

Summary of Contents for RGB108FGEU
































Reviews:

No comments

Brands by name

Popular brands

Load more brands