SOYAL
ACCESS CONTROL SYSTEM
®
AR-881EF/AR-881EV
V110221
AR-881EF
AR-881EV
or
P1
P2
P3
P6
P4
P7
P5
P1
P2
P3
P4
P5
P6
P7
※
1
2
3
1
2
3
4
5
Contents
1
Product
2
User Guide
3
Terminal Cables
4
Tools
Protection Plug
Security Torx Wrenches
Flat Head Hex Socket
Screw: M3x8
Flat Head Cap Philips
Tapping Screw: 4x38
Wire Application Wire
Color
Description
Lock Relay
1
Blue White (N.O.)DC24V1Amp
2 Purple White (N.C.)DC24V1Amp
Common-COM-Point
3
White
(COM)DC24V1Amp
Door Contact
4
Orange
Negative Trigger Input
Exit Switch
5
Purple
Negative Trigger Input
Alarm Relay
6
Gray
Transistor Output Max. 12V/100mA
(Open Collector Active Low)
Power
7
Thick Red DC 12V
8
Thick Black DC 0V
P1
Cable:
Wire Application Wire
Color
Description
Anti-Tamper
Switch
1
Red
N.C.
2
Orange
COM
3
Yellow
N.O.
P5
Cable:
Wire Application Wire
Color
Description
Power
1
Red
DC 12V Output
Security trigger signal 2
Purple
Security trigger signal Output
Arming
3
Red White Arming Output
Duress
4 Yellow White Duress Output
P6
Cable:
Wire Application Wire
Color
Description
1
---
---
2
---
---
TCP/IP Output
3 Orange White Net - RX-
4
Orange
Net - RX+
5 Green White Net - TX-
6
Gerrn
Net - TX+
7
---
---
P3
Cable:
Wire Application Wire
Color
Description
RS-485 for Lift
Controller
1 Thick Green RS-485(B-)
2
Thick Blue RS-485(A+)
P4
Cable:
Wire Application Wire
Color
Description
Beeper
1
Pink
Beeper Output 5V/100mA, Low
LED
2
Yellow
Red LED Output 5V/20mA, Max
3
Brown
Green LED Output 5V/20mA, Max
Door Output
4
Blue White Transistor Output Max. 12V/100mA
(Open Collector Active Low)
Wiegand
5
Thin Green Wiegand DAT: 0 Input
6
Thin Blue Wiegand DAT: 1 Input
WG Door Contact 7
Orange
Negative Trigger Input
WG Exit Switch
8
Purple
Negative Trigger Input
P2
Cable:
External WG keyboard
※
If you want to program system on controller directly, please order WG keyboard then install it according to the following pattern.
Remove the Protection plug that in the bottom left.
(
※
Do not lose protection plug or it will affect the protection level.)
WG Keyboard cable will be connected to the pin board.
WG Keyboard connected to the controller from the bottom left of the hole.
When you finish programming system, please put protection plug back to the
controller.
Installation
Connector Table
Wire Application Wire
Color
Description
Doorbell
1 Black White Transistor Output Max. 12V/100mA
(Open Collector Active Low)
2
Black
GND
P7
Cable:
(For the controller that doorbell function.)
Pull the cables from the square hole of the mounting plate.
Use a screwdriver to screw the base onto the wall.
Connect the terminal cables to the body and attach the body to the mounting plate.
Assemble the covers with the Allen key and screws (accessories supplied).
Turn on the power and LED will light and beep will sound.
※
only provide to the controller that have doorbell function.
P7
