South NET S9 User Manual Download Page 15

                                                                     

NET S9 user manual

 

12 

 

 

2.2 Battery safety 

NetS9 uses built-in rechargeable Li-ion battery. When using the battery, please note: 

 

Warnings

 

a) If the battery discolors and leaks or has other undesirable phenomena, please do         

not use;         

  b) Do not short circuit the battery, disassemble damaged, approaching heat or throw 

in a fire, avoid direct sunlight; 

 c) Do not put the battery in water. 

 

2.3 Battery charge & usage 

The internal battery will automatically recharge when external power is used. Battery before 

first use, please fully charged. If the battery is placed for three months  without using, first 

fully charged, then use it. It will take about 24 hours for full charge. 

 

Warnings

 

a) Do not charge the damage or leaking battery; 

    b) Do not disassemble the battery and charge alone. 

 

2.4 Conserve battery 

The battery should be fully charged before conservation;   

If long-term conservation, please ensure to charge once every three months. 

Summary of Contents for NET S9





















































Reviews: