manualshive.com logo in svg

South-Tek Systems Quick-Check 10, Manual, Page: 18 / 29

Share
Download
South-Tek Systems Quick-Check 10 Manual Download Page 18

Quick-Check PowerSaver Manifold 10 & 20 Port                                                                                      South-Tek 
Systems        

Revision: 0 
Revision Date: 8/30/17 

 

        

 

 

 

     Page 18 of 29  

                                                                                      

 

5.7

 

ZONE HISTORY 

To access the “Zone History” screen, open the “Zone Info” screen in the “Menu” and press the “Zone History” button 
at the bottom of the screen. Zone History can be reset by entering the code “7777” into the box next to “Reset Days” 
button and then press the button. 

5.8

 

COMMUNICATION SETTINGS FOR ETHERNET CONNECTION (OPTIONAL) 

Ethernet communication is an optional feature that can be purchased with each Quick-Check PowerSaver Manifold. 
Once it is included, the user can communicate with the system by assigning a static IP address to the controller and 
entering in that IP address into the controller. Once the static IP is entered, the user must press the connect button or 
cycle  the  power  to  the  controller  to  see  the  device  on  their  intranet  network.  Communication  through  Ethernet 
includes Remote Access, SD Card Access, and MODBUS TCP/IP communication. A connection status message will 
indicate if a successful connection has been made.  

Figure 14: Zone History 

Summary of Contents for Quick-Check 10






























Reviews:

No comments