South bend SB1118 Owner'S Manual Download Page 82

Page: 82 / 84

-80-

For Machines Mfd. Since 10/21

South Bend Tools

Model SB1118

P A R T S

Machine Labels

The safety labels provided with your machine are used to make the operator aware of the

machine hazards and ways to prevent injury. The owner of this machine MUST maintain the

original location and readability of these safety labels. If any label is removed or becomes

unreadable, REPLACE that label before using the machine again. Contact South Bend Tools at

(360) 734-1540 or www.southbendtools.com to order new labels.

Disengage handwheel when using
table controls. Failure to comply could
result in serious personal injury!

WARNING!

SB1118

1 Rev= 1/32"

TABLE UP

TABLE DOWN

MAIN MOTOR

10 FPM

30 FPM

STOP

ERGENCY

WARNING!

INJURY HAZARD

Keep cover closed

while machine is

operating.

Disconnect power

before removing or

servicing.

WARNING!

INJURY HAZARD

Keep cover closed

while machine is

operating.

Disconnect power

before removing or

servicing.

Wiring motor out of phase

may result in machine

damage. After power

connection, if cutterhead

or table moves in wrong

direction, immediately

press emergency STOP

button, disconnect power,

then switch R and T wires

at power feed terminals.

WARNING!

DISCONNECT
POWER BEFORE
ADJUSTMENTS,
MAINTENANCE,
OR SERVICE.

WARNING!

INJURY HAZARD

To reduce risk of short-
and long-term injury,
wear eye, ear, and
lung protection when
using this machine.

INJURY HAZARD

Do not use machine if

you have not read the

manual. Visit

southbendtools.com

or call 360-734-1540

to get a manual.

WARNING!

INJURY HAZARD

Keep cover closed

while machine is

operating.

Disconnect power

before removing or

servicing.

402

401

403

0 0.05"

404

405

406

402

406

407

408

409

410

406

413

411

412

Made in Taiwan to South Bend Specifications

WARNING!

Serial No

MFG Date

MODEL SB1118

25" EXTREME SERIES PLANER

SINCE

1906

Power Requirements: 220V/440V,

3-Phase, 60 Hz

Prewired Voltage: 220V
Main Motor: 15 HP
Full-Load Current Rating: 45A @ 220V,

26.5A @ 440V

Main Motor Speed: 3420 RPM
Cutterhead Speed: 4900 FPM
Cutterhead: Helical w/Indexable Inserts
Number of Replacement Inserts: 174
Feed Rate: 10–30 FPM
Max. Depth of Cut at Full Width: 1/8"
Max. Depth of Cut up to 6" Wide: 1/4"
Max. Cutting Width: 25"
Min. Stock Length: 10"
Min. Stock Thickness: 1/4"
Max. Stock Thickness: 9"
Weight: 1870 lbs.

To reduce the risk of serious injury while using this machine:

  1.  Read and understand owner’s manual before operating.
  2.  Always wear approved safety glasses and respirator.
  3.  Disconnect power before changing inserts, removing parts, or doing

maintenance, service, or adjustments.

4. Properly ground machine—connect to permanently grounded metal

wiring system or an equipment-grounding conductor.

5. Do not wear loose clothing, gloves, jewelry, or other items that can get

entangled. Tie back long hair and roll up sleeves.

  6.  Ensure machine is correctly set up before starting.
  7.  Do not plane two boards of varying thickness at the same time.
  8.  Never plane material smaller than 10" long, 3/4" wide, or 1/4" thick.
  9.  Do not allow hands or clothing to get pulled into cutting area while

feeding workpiece.

10. Stand clear of board ends during cutting operation.
11. Do not plane boards with cracks, loose knots, or other defects.
12. Inserts are sharp! Use extreme caution when changing/adjusting.
13. Never reach into cutting area while machine is running.
14. Keep fingers clear of pinch point between stock and table.
15. Do not operate when tired or under influence of drugs or alcohol.
16. Do not expose to rain or use in wet locations.
17. Prevent unauthorized use by children or untrained users; restrict access or

disable machine when unattended.

WARNING!

INJURY HAZARD

Keep cover closed

while machine is

operating.

Disconnect power

before removing or

servicing.

REF PART #

DESCRIPTION

REF PART #