manualshive.com logo in svg

Sony ZRCT-300, Operating Instructions Manual

Share
Download
Sony ZRCT-300 Operating Instructions Manual Download Page 11

11

If you press the power switch only once in the 
power ON state, the POWER indicator will 
blink red for 2 seconds, but the standby mode 
will not be entered. You can enter standby 
mode by pressing the power switch again 
while the indicator is still blinking red.

2

Turn on the video source equipment.

Turning the power on via Display 
Control Software

The initial settings must be configured 
beforehand to turn the power on via Display 
Control Software. For details, consult your system 
administrator.

1

Start the controller PC, and start Display 
Control Software.

2

Click [Power ON] in the main screen.

Under default settings, all Display Controllers 
and Display Cabinets will turn on.
When a Display Controller turns on, its 
POWER indicator lights green.
When a Display Cabinet turns on, its STATUS 
indicator lights green.

When you click [Standby]

The power status of all connected Display 
Controllers and Display Cabinets will enter 
standby mode, and the main screen will 
remain displayed.
Click [Power ON] to turn the power on again.

3

Turn on the video source equipment.

Turning the power on by connecting the 
power cord to the Display Controller

When [Function] - [System Settings] - [Direct 
Array Power On] is set to [ON] in Display Control 
Software beforehand, simply connecting the 
Display Controller's power cord will turn on the 
Display Controller and Display Cabinets.

1

Connect the power cord to the 

 IN 

connector on the Display Controller.

When a Display Controller turns on, its 
POWER indicator will switch from blinking 
red/orange to remaining lit green.
When a Display Cabinet turns on, its STATUS 
indicator lights green.

2

Turn on the video source equipment.

Turning the Power Off

You can turn off the system’s power using one of 
two methods.
• Turning the power off via the Display Controller
• Turning the power off via Display Control 

Software

Turning the power off via the Display 
Controller

1

Turn off the video source equipment.

2

Press the power switch on the Display 
Controller twice.

The Display Controller and Display Cabinets 
will enter standby mode.

3

If necessary, disconnect the AC power 
supply.

Turning the power off via Display 
Control Software

1

Turn off the video source equipment.

2

Click [Standby] in the main screen of 
Display Control Software.

The Display Controller and Display Cabinets 
will enter standby mode.

3

If necessary, disconnect the AC power 
supply.

Note

Summary of Contents for ZRCT-300







































Reviews:

No comments

Brands by name

Popular brands

Load more brands