50
Basic Operations of the Function Menu
Ch
apt
er 3 Prep
ar
at
ion
s
P3 AUDIO page
a) To enable this setting, the following settings are also required, in the same
way as for volume operations for channels 1 to 4.
• Set the VARIABLE switch of the front panel to “REC” or “PB”.
• Set setup menu item 131 AUDIO VOLUME to “each”.
P4 TC page
P5 OTHER page
Item
Setting
F1: A5 VOL
Sets the volume of audio channel 5.
a)
The volume can be adjusted within the
range from
–200 to 0 to +200
(–
∞
to
+12 dB)
by turning the PUSH SET knob.
The volume changes in steps of ±10 if you
hold the SHIFT button down while you turn
the knob.
F2: A6 VOL
Sets the volume of audio channel 6.
a)
The volume can be adjusted within the
range from
–200 to 0 to +200
(–
∞
to
+12 dB)
by turning the PUSH SET knob.
The volume changes in steps of ±10 if you
hold the SHIFT button down while you turn
the knob.
F3: A7 VOL
Sets the volume of audio channel 7.
a)
The volume can be adjusted within the
range from
–200 to 0 to +200 (–
∞
to
+12 dB)
by turning the PUSH SET knob.
The volume changes in steps of ±10 if you
hold the SHIFT button down while you turn
the knob.
F4: A8 VOL
Sets the volume of audio channel 8.
a)
The volume can be adjusted within the
range from
–200 to 0 to +200 (–
∞
to
+12 dB)
by turning the PUSH SET knob.
The volume changes in steps of ±10 if you
hold the SHIFT button down while you turn
the knob.
F5: –
(Unassigned function button)
F6: –
(Unassigned function button)
Item
Setting
F1: TCG
Selects the timecode signal to which the
internal timecode generator synchronizes.
INT:
Follow the initial value set from the
front panel or remotely from the
device connected to a REMOTE (9P)
connector.
EXT:
Synchronize to external timecode
signal input to the TIME CODE IN
connector.
SYS:
Synchronize to standard reference
timecode signal of a broadcasting
station input to the SYSTEM TC
INPUT connector.
SDI:
Synchronize to timecode embedded
into HD-SDI or SD-SDI signal input to
the HD/SD-SDI INPUT connector.
Note
If you select “EXT” or “SDI” when a DVB-
ASI TS signal is input, the internal
timecode generator synchronizes to
timecode data contained in the TS signal.
F2: PRST/RGN Selects the following for the internal
timecode generator.
PRESET:
Presets an initial value for the
timecode generated by the internal
timecode generator, as specified from
the front panel or remotely from the
device connected to a REMOTE (9P)
connector.
TC:
Generate timecode synchronized to
timecode read by the internal
timecode reader.
VITC:
Generate timecode synchronized to
VITC read by the internal timecode
reader.
F3: RUN
MODE
Selects the timecode run mode.
FREE RUN:
Timecode advances as long
as the unit is powered on, regardless
of the unit’s operating state.
REC RUN:
Timecode advances only
during recording. When you select this
item, also set F1: TCG on this page to
“INT” and set F2: PRST/RGN to
“PRESET”.
F4: DF/NDF
Selects the frame count mode for the
internal timecode generator and the
counter in 59.94i/59.94P/29.97P mode.
DF:
Drop-frame mode
NDF:
Non-drop-frame mode
F5: PDPSET
When the system frequency is set to 1080/
59.94i, 1080/29.97P, or 720/59.94P,
presets the timecode of the A frame of the
pulldown sequence.
24F TC:
Reference timecode for A frame
30F TC:
Timecode after pulldown
conversion from 24-frame timecode
F6: TCR
Selects the type of timecode to display in
the time data display area.
TC:
Display TC.
VITC:
Display VITC.
Item
Setting
F1: INDEX
Sets the index picture (thumbnail) of a clip
being played back
F2: ERR LOG
Displays the error log screen.
F3: CREATE
NEW EDL
Creates a new EDL
F4: ADD TO
CURRENT
EDL
Adds a sub clip to the current EDL
.
F5: PB/EE
a)
Selects the video and audio signals that
are output in stop, forward direction high-
speed search, and reverse direction high-
speed search modes
b)
.
PB:
Playback signal
EE:
EE mode signal
Item
Setting
