manualshive.com logo in svg

Sony XDCAM PDW-HR1, Operation Manual, Page: 160 / 214

Share
Download
Sony XDCAM PDW-HR1 Operation Manual Download Page 160

160

Setup Menu

  

C

h

ap
te

r 8

  

M

enu

s

843

AUDIO OUTPUT ARRANGE

Specify the mixing of audio/voice data output signals.

Note

This appears when the PDBZ-UPG03 Software Upgrade Key or PDBK-
MK1 option board is installed.

See “To set up mixing of audio/voice data output signals” (page 122) for 
more information about how to set up mixing.

Menu items in the 900s, relating to digital process (DIGITAL PROCESS)

Item number

Item name

Settings

920

SD-SDI H-ANC CONTROL

Select whether to add information to the SDI output.

Sub-item

1

AUDIO 5CH-8CH

off:

 Do not add digital audio data channels 5 to 8.

on:

 Add digital audio data channels 5 to 8.

2

RP188 ATC

off:

 Do not add RP188 timecode data.

on:

 Add RP188 timecode data.

923

AUTO SQUEEZE

Select whether to use auto squeeze mode. 

off:

 Do not use.

on:

 Use.

925

HDMI OUTPUT SELECT

Select the resolution of the video output from the HDMI OUT connector.

hd (1080i/720P)
sd-I (480i (576i))
sd-p (480P (576P))

930

DOWN CONVERTER MODE 

Select the down-converter mode.

CROP (EDGE CROP):

 Select the edge-crop mode.

L-BOX (LETTER BOX):

 Select the letter box mode.

SQUEZ (SQUEEZE):

 Select the squeeze mode.

931

DOWN CONVERTER LETTER BOX 
MODE

Select the aspect ratio of the down-converter output when menu item 930 
is set to “l-box”.

16:9: 

Set the aspect ratio of the HD-SD converter output to 16:9.

14:9:

 Set the aspect ratio of the HD-SD converter output to 14:9.

13:9:

 Set the aspect ratio of the HD-SD converter output to 13:9.

932

H CROP POSITION (DC)

Adjust the H-crop (the horizontal position when cropping in the edge crop 
mode) of the down converter output when menu item 930 is set to “crop”.

–120 (–120 (DEC)) to 0 (0 (DEC)) to 120 (120 (DEC))

934

CROSS COLOR (DC)

Adjust the down-converter cross color.

0 (0 (DEC)) to 8 (8 (DEC)) to 15 (15 (DEC))

935

DETAIL GAIN (DC)

Adjust the down-converter image enhancer, the sharpness of edge 
enhancement.

0 (0 (HEX)) to 7F (7F (HEX))

936

LIMITER (DC)

Adjust the down-converter image enhancer, the maximum detail level 
added to emphasize the original signal.

0 (0 (HEX)) to 20 (20 (HEX)) to 3F (3F (HEX))

937

CRISP (DC)

Adjust the down-converter image enhancer, the threshold amplitude at 
which low amplitude signals are not emphasized.

0 (0 (HEX)) to F (F (HEX))

938

LEVEL DEPEND THRESHOLD 
(DC)

Adjust the down-converter image enhancer. Set the luminance range for 
edge enhancement.

0 (0 (HEX)) to 8 (8 (HEX)) to F (F (HEX))

939

H DETAIL FREQUENCY (DC)

Adjust the down-converter image enhancer. Set the central frequency for 
edge enhancement.

2.6M (2.6 (MHz)), 3.4M (3.4 (MHz)), 3.9M (3.9 (MHz)), 4.6M (4.6 (MHz))

940

H/V RATIO (DC)

Adjust the down-converter image enhancer. Set the horizontal/vertical 
ratio for edge enhancement.

0 (0 (DEC)) to 3 (3 (DEC)) to 7 (7 (DEC))

Menu items in the 800s, relating to audio control (AUDIO CONTROL)

Item number Item name

Settings

Summary of Contents for XDCAM PDW-HR1























































































































































































































Reviews:

No comments