Sony XDCAM PDW-HR1 Operation Manual Download Page 151

Page: 151 / 214

151

Setup Menu

Ch
apt

er 8

308

SELECTION OF STD/NON-STD
FOR COMPOSITE VIDEO IN

Select the STD or NON-STD mode in accordance with a composite
video input.

STD (forced STD):

The STD mode is always used (forced STD mode).

N-STD (forced non-STD):

Use this setting when the input video signal

is unstable (forced NON-STD mode).

Notes

• When using a VCR with no built-in time base corrector (e.g. a home-

use VHS-system VCR), select “N-STD”.

• When this item is set to “N-STD”, the following limitations apply,

because this unit’s sync reference signal generator always
synchronizes to an internal sync reference signal

(see page 50)

- It is not possible to record VITC, wide picture information, or closed

captions, which is multiplexed into the vertical blanking interval of
composite video signals.

- Lip-sync delays (delays in the synchronization of video and audio)

may occur.

320

DIGITAL AUDIO PB PROCESS ON
EDIT POINT

Select the treatment of audio playback at edit points.

cut:

Carry out a cut (possibly resulting in audio discontinuities at the edit

point).

fade:

Fade out and fade in.

345

EDITING MODE

Selects the edit mode in edit list editing.

ovl (overlay):

Overlay mode

ins (insert):

Insert mode

del (delete):

Delete mode

346

PLAYER SELECT

Selects the source of the clips to be used as material.

clip (disc(clip)):

Clips (video and audio data) on a disc inserted into the

recorder

ext (external):

External device

voice (disc(voice)):

Audio (audio data, distinct from clips) on a disc

inserted into the recorder

sxs (SxS):

Clips (video and audio data) on an SxS memory card

inserted into the recorder

Note

The settings “voice (disc(voice))” and “sxs (SxS)” appear when the
PDBZ-UPG03 Software Upgrade Key or PDBK-MK1 option board is
installed.

347

INPUT VOICE CH

Selects the audio input channel.

CH 1 to CH 8

Note

This appears when the PDBZ-UPG03 Software Upgrade Key or PDBK-
MK1 option board is installed.

348

OUTPUT VOICE CH

Selects the output channel for a voice track.

CH 1 to CH 8

Notes

• This appears when the PDBZ-UPG03 Software Upgrade Key or

PDBK-MK1 option board is installed.

• The current setting of this item at the start of editing is applied across

the entire edit list. It is not possible to change this setting for different
voice data segments.

Menu items in the 400s, relating to preroll (PREROLL)

Item number Item name

Settings

401

FUNCTION MODE AFTER CUE-UP Select the state that the unit goes into after a cuing-up operation.

stop:

Stops (the stop mode).

still:

Still playback (in jog and shuttle mode).

Menu items in the 300s, relating to editing operations (EDITING)

Item number Item name

Settings

Summary of Contents for XDCAM PDW-HR1























































































































































































































Search results

Summary of Contents for XDCAM PDW-HR1

Reviews:

Sony XDCAM PDW-HR1, Operation Manual, Page: 151 / 214

Search results

Summary of Contents for XDCAM PDW-HR1

Reviews: