manualshive.com logo in svg

Sony XDCAM PDW-HR1, Operation Manual, Page: 143 / 214

Share
Download
Sony XDCAM PDW-HR1 Operation Manual Download Page 143

143

Setup Menu

  

Ch
apt

er 8  

Me

n

u

s

013

SYSTEM FREQUENCY 
SELECT MENU

Specify whether to enable switching the system frequencies (59.94i, 59.94P, 
29.97P, 50i, 50P, 25P, 23.98P).

off

: Do not enable switching the system frequencies.

on

: Enable switching the system frequencies.

For details about switching the system frequencies, see page 51.

Note

Settings for both basic and extended menu items are saved separately for 
different system frequencies.
• 1080 59.94i/29.97P
• 1080 50i/25P
• 1080 23.98P
• 720

59.94P

• 720

50P

Therefore, when you switch system frequencies, all menu items are reset to 
the current settings for the new mode. (They are different from the setting for 
the previous mode.)

016

ALARM DISPLAY

Select whether to display alarm messages.

off: 

Do not display alarm messages. (However, certain important alarms are 

displayed.)

limit (on (limited)):

 Display only a minimum number of alarm messages.

on:

 Display all alarm messages.

For details about alarm message display conditions, see “Alarms” 
(page 177).

017

SUB STATUS DISPLAY SELECT Determine the kind of sub status information to be output from the 

COMPOSITE OUT connector, the SDSDI OUTPUT connector, or the 
HDSDI OUTPUT 2 (SUPER) connector.

off:

 Do not output sub status information.

rmain (disc remain):

 Available disc space (unit: minute)

clip (clip no):

 Order of playback of the selected clip/total number of clips

pbr (playback remain):

 The remaining playback time of the selected clip 

from the current playback position (hours:minutes:seconds:frames).

Note

When menu item 005 is set to “off”, sub status information is not displayed 
when this item is set to anything other than “off”.

024

MENU CHARACTER TYPE

Determine the type of characters in menu text output from the COMPOSITE 

OUT connector, the SDSDI OUTPUT connector, or the HDSDI OUTPUT 2 
(SUPER) connector for superimposed display on the monitor.

white:

 White letters on a black background.

black:

 Black letters on a white background.

W/out:

 White letters with black outline.

B/out:

 Black letters with white outline.

Set this item by selecting the required type while viewing the monitor.

027

SD CHARACTER

 a)

Specifies whether to superimpose text information on the video signals 
output from the COMPOSITE OUT and SDSDI OUTPUT connectors.

off:

 Do not superimpose.

all:

 Superimpose on the output of both the COMPOSITE OUT and SDSDI 

OUTPUT connectors.

comp (composite):

 Superimpose on the output of the COMPOSITE OUT 

connector.

sdi:

 Superimpose on the output of the SDSDI OUTPUT connector.

028

HD CHARACTER

 a)

Specify whether to superimpose text information on the video signal output 
from the HDSDI OUTPUT 2 (SUPER) connector.

off:

 Do not superimpose.

sdi2 (hd-sdi2):

 Superimpose.

Item number Item name

Settings

Summary of Contents for XDCAM PDW-HR1























































































































































































































Reviews:

No comments