Locations and Functions of Parts and Controls
30
Chapt
er
1
Ov
er
v
ie
w
FAN (flashing):
The cooling fan is operating at
low speed, but the temperature inside the unit
has risen to a level just below the level at
which an alarm occurs.
Note
If you do nothing while the FAN display is flashing, the
unit will attempt to lower the internal temperature by
operating the fan at high speed. When the FAN display
begins to flash, you should stop shooting and other
operations and wait until the internal temperature drops,
and then restart operations.
l
GPS reception status
For details, see “Icons displayed on the screen”
(page 103).
m
Memory symbol and remaining
capacity, wireless LAN connection
status, or CBK-WA100 Wireless
Adaptor remaining media status
When a USB flash drive is connected to the
enabled USB connector, a memory symbol
appears indicating the mount status of the USB
flash drive and its remaining capacity.
Memory symbol and remaining capacity display
a) Use a USB flash drive with enough free capacity
remaining.
b) Enable the proxy data recording function.
c) Clear the write protection on the USB flash drive.
d) Format or exchange the USB flash drive.
When Wi-Fi on the POWER SAVE page of the
OPERATION menu is set to “ENABL”, the
wireless LAN connection status is displayed in
this area, as follows.
Not connected, or connection destination
unknown:
An “×” lights.
Connecting:
Four gray segments flash.
Connection completed (signal strength 0):
One
gray segment lights.
Connection completed (signal strength 1 to 4):
White segments light. The number of white
segments (1 to 4) indicates the reception
signal level (1 to 4).
When the optional CBK-WA100 Wireless
Adaptor is connected via USB, the remaining
media capacity on the CBK-WA100 is displayed
if Wi-Fi/ETHER_RM is set to “RM” or “ALL”
on the CAM CONFIG 3 page of the
MAINTENANCE menu.
n
Wireless adaptor reception status
Displays the reception status of the optional
CBK-WA100.
LTE connections:
Displays 3G/4G symbol.
Station mode:
Displays 4-bar signal strength.
Access point mode:
Displays AP symbol.
Bottom of viewfinder screen
a
External device control and single clip
playback
REC2:
Appears when HDSDI REMOTE I/F is
set to “CHARA” and SDI REC CONTROL
is set to “RM” on the CAM CONFIG 1 page
of the MAINTENANCE menu, and the
camcorder is remotely controlling recording
on external devices connected to the SDI
OUT 1/2 connectors (HDSDI output).
1)
REC2 P PARALLEL REC:
Appears when
HDSDI REMOTE I/F is set to “CHARA”
and SDI REC CONTROL is set to “PARA”
on the CAM CONFIG 1 page of the
MAINTENANCE menu, and the camcorder
Icon
Remaining
capacity
display
Description
Lit
Proxy data recording is
enabled, and there is at least
5 minute of remaining
capacity.
Flashing
Proxy data recording is
enabled, but there is less
than 5 minute of remaining
capacity.
a)
Out
Proxy data recording is
disabled.
b)
INH
The USB flash drive is write
protected.
c)
Out
The USB flash drive could
not be mounted.
d)
a
b
c
defghij k
n
m
l
E X Z
W 13.4V
99
1 2
H D 4 2 2 5 0 E 0 0 0 1 : 0 0 1 / 0 0 4 D C I N
C O N T
F A N
13.9
35-30
K +
W H I T E : N G
L E V E L T O O H I G H E X T
R E C 2 T C G 0 1 : 2 3 : 4 5 : 1 5 H D S D I
1 - 125C
L O W L I G H T
5600
F1.7
18
35 30
dB 1/ 2000
1
2
W:A
Ext.
3G/4G
