4
MZ-N910
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electro-
static break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
Never look into the laser diode emission from right above when
checking it for adjustment. It is feared that you will lose your sight.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
(ABX-1R)
The laser diode in the optical pick-up block may suffer electro-
static break-down easily. When handling it, perform soldering
bridge to the laser-tap on the flexible board. Also perform mea-
sures against electrostatic break-down sufficiently before the op-
eration. The flexible board is easily damaged and should be handled
with care.
SECTION 1
SERVICING NOTES
• In performing the repair the power supplied to the set, remov-
ing the MAIN board causes the set to be disabled.
In such a case, perform soldering bridge to SL802 on MAIN
board.
laser-tap
OPTICAL PICK-UP FLEXIBLE BOARD
MAIN board
FLEXIBLE board
(over write head)
• Handle the FLEXIBLE board (over write head) with care, as it
has been soldered directly to the MAIN board.
In repairing the component side of MAIN board, connect the
FLEXIBLE board (over write head) and the MAIN board with
the lead wires in advance.
System requirements
The following hardware and software are required in order to use the
SonicStage software for the Net MD.
This software is not supported by the following
environments:
•
Macintosh
•
Windows XP versions other than Home Edition or Professional
•
Windows 2000 versions other than Professional
•
Windows 98 versions other than Second Edition
•
Windows NT
•
Windows 95
•
Personally constructed PCs or operating systems
•
An environment that is an upgrade of the original manufacturer-installed
•
Multi-boot environment
•
Multi-monitor environment
Notes
•
We do not ensure trouble-free operation on all computers that satisfy the
•
We do not ensure trouble-free operation of the system suspend, sleep, or
hibernation function on all computers.
Computer IBM PC/AT or Compatible
• CPU: Pentium II 400 MHz or higher
(Pentium III 450 MHz or higher is recommended.)
• Hard disk drive space
1)
: 120 MB or more
•
1)
Others
• CD-ROM drive (capable of digital playback by WDM)
• Sound Board
•
Operating
System
Factory installed:
Windows XP Home Edition/Windows XP Professional/
Windows Millennium Edition/Windows 2000 Professional/
Windows 98 Second Edition
Display
High Color (16bit) or greater, 800
×
480 dots or more
Others
• Internet access: for Web registration and EMD services
•
Note on hard disk drive space
120 MB or more free space on the hard disk drive is required. If your
computer does not have enough space, the software will not be properly
installed. The required free space differs according to the version of
your Windows OS, or the amount of audio files that you handle.
USB port (supports USB 2.0 Full Speed
(previously USB 1.1))
(800
×
600 dots or more is recommended)
Windows Media Player (version 7.0 or higher) installed for
playing WMA files
RAM: 64 MB or higher
(128 MB or higher is recommended)
operating system
system requirements.
MAIN BOARD
(SIDE A)
SL802
• Replacement of SN761058AZQLR (IC501), CXD2680-205GA
(IC801) used in this set requires a special tool
• The shipment data will be cleared when the NV is reset. There-
fore, change the NV adjusted values following the Change of
NV Adjusted Values immediately after the NV was reset. (See
page 18)
• This set requires the patch data in the nonvolatile memory
(IC851) to be rewritten using the application, when the MAIN
board was replaced. (See page 29)
