Sony Walkman MZ-N910 Page 28 Service Manual Download

Page: 28 / 65

MZ-N910

Item No.

Description

434

TWPP gain adjustment

431

TWPP offset adjustment 1

432

TE offset adjustment 2

449

TWPP OP offset adjustment

410

WRITE

READ selection

411

TWPP offset adjustment 1

412

TE offset adjustment 2

418

TWPP OP offset adjustment

490

HCLV

LCLV selection process

450

HEAD DOWN

•

GRV servo ON

460

READ

WRITE selection

461

TE gain adjustment

463

TEIN offset adjustment

470

Tracking servo ON

471

TWPP offset adjustment 1

476

ABCD gain adjustment

484

Focus gain adjustment

485

Tracking gain adjustment

451

TWPP offset adjustment 1

452

TE offset adjustment 2

460

READ

WRITE selection

470

Tracking servo ON

474

TWPP gain adjustment

471

TWPP offset adjustment 1

472

TE offset adjustment 2

489

TWPP OP offset adjustment

450

WRITE

READ selection

451

TWPP offset adjustment 1

452

TE offset adjustment 2

458

TWPP OP offset adjustment

448

30 sec continuous REC

400

GRV setting

•

servo OFF

•

HEAD UP

READ GRV adjustment 2

120

Focus servo ON

130

Tracking servo ON

138

RF gain adjustment

141

FOCUS_BIAS

035

Stray light offset measurement

100

R_GRV setting

•

servo OFF

Resume Clear

Perform the Resume clear when all adjustments completed.

• Resume clear setting method

1. Select the manual mode of the test mode, and set item number

043 (see page 13).

2. Press the

key.

3. Press the

key to return to the test mode (display check

mode).

Remote commander LCD display

Resume 00

043

Remote commander LCD display

Resume clear complete

Res***

043

ResClr

043

Summary of Contents for Walkman MZ-N910


































































Search results

Summary of Contents for Walkman MZ-N910

Reviews:

Related manuals for Walkman MZ-N910

Brands by name

Popular brands

Sony Walkman MZ-N910, Service Manual

Search results

Summary of Contents for Walkman MZ-N910

Reviews:

Related manuals for Walkman MZ-N910

Brands by name

Popular brands