3
D-FS601
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the charged
electrostatic load, etc. on clothing and the human body. During repair, pay
attention to electrostatic breakdown and also use the procedure in the printed
matter which is included in the repair parts.
The flexible board is easily damaged and should be handled with care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on the disc
reflective surface by the objective lens in the optical pick-up block. Therefore,
when checking the laser diode emission, observe from more than 30cm away
from the objective lens.
Before Replacing the Optical pick-up Block
Please be sure to check thoroughly the parameters as per the “Optical pick-
up Block Checking Procedure” (Part No. : 9-960-027-11) issued separately
before replacing the optical Pick-up block.
Note and specifications required to check are given below.
• FOK output : IC601
yg
pin (TP610)
When checking FOK, remove the lead wire to disc motor.
• RF signal P-to-P value : 0.4 to 0.5Vp-p
SECTION 1
SERVICING NOTES
Laser Diode Checking Methods
During normal operation of the equipment, emission of the laser diode is
prohibited unless the upper panel is closed while turning ON the S801 (push
switch type).
The following two checking methods for the laser diode are operable.
Method :
Emission of the laser diode is visually checked.
1. Open the upper lid.
2. Push the S801 as shown in Fig. 1 .
3. Check the object lens for confirming normal emission of the laser diode.
If not emitting, there is a trouble in the automatic power control circuit or
the optical pick-up. During normal operation, the laser diode is turned
ON about 2.5 seconds for focus searching.
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR
BASE UNIT
TABLE OF CONTENTS
Fig. 1 Method to push the S801
S801
1. SERVICING NOTES
······················································· 3
2. GENERAL
·········································································· 4
3. DISASSEMBLY
································································ 6
3-1. Upper Lid, Middle Cabinet ··········································· 6
3-2. MD Assy (CDM-3125ER), MAIN Board ····················· 7
3-3. Turn Table Motor Assy (Spindle) (M901) ····················· 7
3-4. Motor Assy (Sled) (M902), Optical Pick-up
(DAX-25E) ···································································· 8
3-5. SWITCH Board, Hold Lever ········································· 8
4. ELECTRICAL ADJUSTMENTS
································· 9
5. DIAGRAMS
······································································ 11
5-1. Block Diagrams – MAIN Section – ···························· 12
– TUNER Section – ····················································· 13
5-2. Printed Wiring Board – MAIN Board (Side A) – ······· 14
5-3. Printed Wiring Board – MAIN Board (Side B) – ······· 15
5-4. Schematic Diagram – MAIN Board (1/5) – ··············· 16
5-5. Schematic Diagram – MAIN Board (2/5) – ··············· 17
5-6. Schematic Diagram – MAIN Board (3/5) – ··············· 18
5-7. Schematic Diagram – MAIN Board (4/5) – ··············· 19
5-8. Schematic Diagram – MAIN Board (5/5) – ··············· 20
5-9. Printed Wiring Board – SWITCH Board – ················ 21
5-10. Schematic Diagram – SWITCH Board – ··················· 22
5-11. IC Pin Function Descriptions ······································ 23
5-12. IC Block Diagrams ······················································ 27
6. EXPLODED VIEWS
······················································ 28
6-1. Upper Lid Section ······················································· 28
6-2. Cabinet Section ··························································· 29
6-3. Cabinet Lower Section ················································ 30
6-4. Optical Pick-up Section (CDM-3125ER) ···················· 31
7. ELECTRICAL PARTS LIST
······································· 32