Sony VSPA-D7 Setup Instructions Download Page 11 | Manualshive

Page: 11 / 21

Sony VSPA-D7 Setup Instructions Download Page 11

11

Installation

Installation

After setting a network address for all the players and
registering the players with the VSPA-D7 software, install
each player in its actual operating location and connect
them as shown in the figure below.

For details such as how to install rubber feet on a player
and how to install a player onto the back of a professional
display device, refer to the player’s Operating
Instructions.

• Connect a display device to the

connector of each

player with an RGB cable. If a player is not connected to
a display device, it cannot start operation.

• The figure above shows an example of controlling the

display device using an RS-232C connection. A display
device can be controlled from a player via a network,
depending on the model of the display device.
In such a case, the connection between the

1

connector and the RS-232C connector of the display
device is not required. Instead, connect the display
device to the network.

• Be sure to use the upper

1 as the serial connector

for the player that you want to connect to the display
device.
This

1 connector is a dedicated connector for

controlling display devices in this system. Be careful
that if a non-supported device is connected to it and data
is sent to the connector, it may result in a malfunction.

Network (Internet/intranet)

Computer

(Running the VSPA-D7
Management Software)

VSP-NS7
Digital Signage Player

1

RS-232C
connector

Analog RGB
connector

Speaker

Display device

Speaker

Notes

«
...
9
10
11
12
13
...
»

Summary of Contents for VSPA-D7






















Reviews:

No comments